2. Copyright © 2018 by SAI DEEPA ROCK DRILLS PVT. LTD. All rights reserved. No part of this publication may be reproduced, distributed, or transmitted in any form or by any means, including photocopying, recording, or other electronic or mechanical methods, without the prior written permission of Sai Deepa Rock Drills Pvt. Ltd . For permission requests, write to Saideepa Rock Drills Pvt Ltd. Attention: Permissions Coordinator,” at the address mentioned on the back page.

1. 1 DTH PRODUCT CATALOGUE

36. 36 DTH PRODUCT CATALOGUE

4. 4 DTH PRODUCT CATALOGUE GLOBAL CLIENTELE

10. 10 DTH PRODUCT CATALOGUE SD Shanks

14. 14 DTH PRODUCT CATALOGUE Panther Shanks

16. 16 DTH PRODUCT CATALOGUE BR Shanks

19. 19 DTH PRODUCT CATALOGUE Mach Shanks

22. 22 DTH PRODUCT CATALOGUE DHD Shanks

27. 27 DTH PRODUCT CATALOGUE QL Shanks

30. 30 DTH PRODUCT CATALOGUE RK Shanks

95. 95 DTH PRODUCT CATALOGUE

8. 8 DTH PRODUCT CATALOGUE BIT SHANK IDENTIFICATION CHART BR3 DHD 340 DHD 380 SD6 SD12 BR33 DHD 350 SD4 SD8 QL40 6 SPLINES 8 SPLINES 8 SPLINES 8 SPLINES 8 SPLINES 6 SPLINES 8 SPLINES 10 SPLINES 8 SPLINES 8 SPLINES 7 SPLINES 8 SPLINES 8 SPLINES 8 SPLINES 10 SPLINES 165 mm 208.5 mm 165 mm BR2 DHD 3.5 DHD 360 SD5 SD10 470 mm 320.5 mm 350 mm 260 mm 324 mm 356 mm 279 mm 181 mm 308 mm 165 mm 260 mm 260 mm

9. 9 DTH PRODUCT CATALOGUE BIT SHANK IDENTIFICATION CHART QL60 PANTHER MACH44 RK1 PUMA QL80 DHD 17 MX40 RK3 12 SPLINES 6 SPLINES 8 SPLINES 8 SPLINES 12 SPLINES 6 SPLINES 8 SPLINES 8 SPLINES 12 SPLINES 16 SPLINES 8 SPLINES 8 SPLINES 10 SPLINES 240 mm 170 mm 265 mm 192 mm 280 mm 253.5 mm QL50 CHEETHA MACH303 MACH50 243.7 mm 324 mm 335.8 mm 324 mm 332.5 mm 243.7 mm QLX40 TD40 12 SPLINES 12 SPLINES 209 mm 208.9 mm 134.9 mm 12 SPLINES NUMA 490.5 mm RC5 6 SPLINES 263 mm

82. 82 DTH PRODUCT CATALOGUE OTHER DTH PRODUCTS

94. 94 DTH PRODUCT CATALOGUE NOTES

43. 43 DTH PRODUCT CATALOGUE JDM SERIES - 3.5” JDM35MD / DH - 4.5” JDM45DH / QLX - 5.0” JDM55QL / DH - 6.0” JDM60QL / DH - 8.0” JDM80QL / DH - 10.0” JDM10SD - 12.0” JDM 12SD • JDM Series is a valve less type hammers designed for high performance at low operating air pressures. • Suitable bits has a strong robust design without foot valve to withstand heavy duty application. • JDM Series Hammers maximizes energy output and reduces service requirements. • Wear Sleeve is not reversible except JDM60QL • All critical internal components are heat treated under strict control to maximize tool longevity. • A built-in choke facility allows the driller to adjust the volume of air through the hammer to optimize cuttings evacuation. • Robust piston design for optimum strength and performance • Fitted with a reversible cylinder to maximize operating life. • Multi-start threads on backhead and chuck ensure easy coupling / uncoupling of hammer. • Excellent for all types of drilling applications including residential geothermal, production quarry drilling, seismic drilling and small construction drilling. • Water Well • Mining • Construction • Quarry JDM Series Air Consumption DESIGN HIGHLIGHTS EXCLUSIVE FEATURES APPLICATIONS

96. 96 DTH PRODUCT CATALOGUE Plot no 106 & 107, Phase II IDA Cherlapally, Hyderabad – 500051 Telangana, India. Ph : +91-40-27260217 +91-40-27260438 Fax : +91-40-27261231 Email: info@saideepa.com sales@saideepa.com Web: www.saideepa.com SAI DEEPA ROCK DRILLS PVT. LTD. © SAI DEEPA DTH PRODUCT CATALOGUE V3.0 2023 ISO 9001: 2015 | 14001:2015 | 45001:2018 | 27001:2013

5. 5 DTH PRODUCT CATALOGUE Sai Deepa Rock Drills Pvt.Ltd. is one of the leading manufacturers of rock drilling tools and Mining Equipment in India. The product range includes DTH Hammers, DTH Button Bits, Drifter Bits and related products used in water well drilling, Mining, Tunneling, Quarrying and Construction Industries. The company products are acceptable globally in more than 50 countries. The company has set up a state of the art production facilities for manufacturing of Rock Drilling Tools and Mining equipment’s which includes excellent CNC equipped Machine shop, Heat Treatment with Seal Quenching Furnaces, Metallurgical laboratory, Quality Control Department and Surface Treatment plant. Stringent Quality Systems are adopted to produce world class products at most competitive prices. The company has a dedicated Research and Development unit where the skilled engineers are continuously involved in upbringing durable product designs to give products a total reliability, high productivity and complete customer satisfaction. INTRO Saideepa has established and applied Quality management system ISO 9001:2015, Environment management system ISO 14001:2015, Occupational health and Safety management system ISO 45001:2018 and Information security management system ISO 27001:2013 for design, manufacturing and supplying of DTH hammers and button bits. Our Integrated management system are inspected by DNV.GL from Norway and United Kingdom Accreditation Service (UKAS) from UK awarded us above all certificates. • Safety • Customer Success • Team Play • Environmental Protection • Information Security SDRD recognizes that it is possible to produce quality products only from the best raw materials. All the SDRD products are made from the alloy steels having very high quality levels. The steels are procured from the best alloy steel manufactures available both in India and abroad. The composition of the steel is selected very precisely to give the best final properties to the product. ABOUT SAIDEEPA STANDARDS CORE VALUES RAW MATERIAL

7. 7 DTH PRODUCT CATALOGUE Sai Deepa Rock Drills manufactures extensive range of DTH Bits and Hammers with good quality and most economical. Our products are suited to all type of drilling like Water well, Mining, Construction and Quarry. Our products are the preferred by drilling engineers in many countries because of their precision design and efficient drilling during use. We manufacture wide range hammers with suitable bits for different applications. The bit range varies from 3” to 20” (diameter) with different face styles like Concave, Convex and Flat. The hammer range varies from 2.5” to 18”. SDRD products are designed, engineered and manufactured, for superior penetration while maintaining maximum cleaning action at the face of the bit, thus extending the working of the product. Products are field tested to stringent quality requirements to provide consistent performance results in the field. Bits are conditioned by a special manufacturing procedure which establishes a protective cushion on the bits, thus reducing chances of cracking which often occur in hi-impact drilling products. Products are heat treated applying most advanced heat treatment technology that extends the product life for maximum wear and performance in the toughest of drilling conditions. Relevant quality checks are applied in various stages of manufacture. Saideepa products are manufactured right from raw material to finsh stage, All in house production efficiency using advance technology with international standards. The combination of premium steel, carbide, state of the art design and manufacturing Techniques, yields a superior product, capable of performing in the toughest of drilling conditions. . . . . . . . . . . DTH BITS & HAMMERS FEATURES & BENEFITS

67. 67 DTH PRODUCT CATALOGUE DRT SERIES - 9.0” DRT9RK - 12.0” DRT11R3 / FD11 • DRT Series is a valve less type hammers designed for high performance at low operating air pressures. • Suitable bits has a strong robust design without foot valve to withstand heavy duty application. • DRT Series Hammers maximizes energy output and reduces service requirements. • Wear Sleeve is reversible. • All critical internal components are heat treated under strict control to maximize tool longevity. • Water Well • Mining • Construction • Quarry • Hammer is inbuilt with buffer ring and metal spacer, to sustain the compressive load generated from drill string. • Lock plates are used for locking the control tube and drive sub spacer is used for easy coupling / uncoupling of drive sub. • Hammer is designed with the adjustable Choke which allows you to adjust the volume of air that is used to power the Piston. DESIGN HIGHLIGHTS EXCLUSIVE FEATURES APPLICATIONS DRT Series Air Consumption

70. 70 DTH PRODUCT CATALOGUE UDC SERIES - 3.7" UDC 37DH - 4.0" UDC 40DH - 4.7" UDC 47DI • UDC Series is a valve less type hammers designed for high performance at low operating air pressures. • Suitable bits has a strong robust design without foot valve to withstand heavy duty application. • UDC Series Hammers maximizes energy output and reduces service requirements. • Wear Sleeve is not reversible. • All critical internal components are heat treated under strict control to maximize tool longevity. • A built-in choke facility allows the driller to adjust the volume of air through the hammer to optimize cuttings evacuation. • Unique internal mounting of liner eliminates the need for seating ring. • Fewer internal components minimize service requirements. • Multi-start threads on backhead and chuck ensure easy coupling / uncoupling of hammer. • Excellent for all types of drilling applications typically for water well drilling and geothermal applications. • Water Well • Mining • Construction • Quarry UDC Series Air Consumption DESIGN HIGHLIGHTS EXCLUSIVE FEATURES APPLICATIONS

6. 6 DTH PRODUCT CATALOGUE BIT FACE STYLES Concave Convex Flat This button is the most common shape utilized in DTH bits. This type of shape is the strongest and most resistant to breakage. The domed shape provides excellent penetration in medium rock, hard rock, and hard rock broken formations, in all types of drilling. Suitable for all soft and medium rock conditions including fractured and fissured rocks. Spherical (Dome) Ballistic Parabolic BUTTON SHAPES This face has been utilized in medium hard to hard drilling formation. Face design allows for increased body support for gauge carbide. There are two gauges and the inner gauge row helps to protect the outer row from excessive wear. The convex style tends to keep the drilling face intact longer by drilling with the two rows of the buttons on the convex face. This face style gives good hole pene - tration in medium to hard rock formations This is the common face style used in market. Cone shaped depression in the face has centering effect for straighter holes. It gives excellent penetration in soft to medium hard rock formation. This bit is very aggressive in drilling application and is suited best for hard to very hard rock and broken formation. Face slots help eliminate bit plugging in softer zones. More carbide to surface contact for better rock fracture. It is a simple and robust design well suited for hard to very hard rock formation. Normally this button is used in less hard consolidated drilling formations. This type of button is very aggressive and drills faster than domed. However, because the ballistic tip protrudes out farther than domed, the ballistic is prone to breakage if used in the wrong formations. Care should be taken when drilling with this type of button. Ballistic buttons yield high penetration rates and efficient rock breakage.

62. 62 DTH PRODUCT CATALOGUE D SERIES - 4.5” S45S4 - 5.5” D55DI - 6.5” DM65DI - 8.0” D80M • D Series is a valve less type hammers designed for high performance at low op - erating air pressures. • Suitable bits has a strong robust design without foot valve to withstand heavy duty application. • D Series Hammers maximizes energy output and reduces service requirements. • Wear Sleeve is reversible except DMD40DH and DMD50DH • All critical internal components are heat treated under strict control to maximize tool longevity. • Simplified piston geometry for improved balance and location within cylinder. • Improved chamber volumes and cycle timing to optimize performance • Suitable for drilling at a wide range of air pressures, excelling at higher working pressure. • Fitted with a reversible cylinder to maximize operating life. • Fewer internal parts minimize service requirements • Water Well • Mining • Construction • Quarry D Series Air Consumption DESIGN HIGHLIGHTS EXCLUSIVE FEATURES APPLICATIONS

40. 40 DTH PRODUCT CATALOGUE WINNER SERIES - 3.5” WIN35DH - 4.5” WIN45DH / MX • WINNER Series is a valve type hammers designed for high performance at low operating air pressures. • Suitable bits has a strong robust design with and without foot valve to withstand heavy duty application. • WINNER Series Hammers maximizes energy output and reduces service requirements. • Wear Sleeve is not reversible. • All critical internal components are heat treated under strict control to maximize tool longevity. • Water Well • Mining • Construction • Quarry • Hammer is inbuilt with buffer ring which will sustain the compressive load generat - ed from drill string. • Flapper mechanism helps to adjust inflow air pressure so as to increase the volume of air to be occupied. • Inner cylinder guides piston and supplies air into piston area where the air flow is controlled. Winner Series Air Consumption DESIGN HIGHLIGHTS EXCLUSIVE FEATURES APPLICATIONS

51. 51 DTH PRODUCT CATALOGUE JDC SERIES - 4.5” JDC45S - 5.0” JDC55QL / DH - 6.0” JDC60QL / DH - 8.0” JDC80QL / DH -10.0” JDC10SD • JDC Series is a valve less type hammers designed for high performance at low operating air pressures. • Suitable bits has a strong robust design without foot valve to withstand heavy duty application. • JDC Series Hammers maximizes energy output and reduces service requirements. • Wear Sleeve is not reversible. • All critical internal components are heat treated under strict control to maximize tool longevity. • Water Well • Mining • Construction • Quarry • Hammer is designed with the adjustable Choke which allows you to adjust the volume of air that is used to power the Piston. • With help of steel make up ring and lock ring it will able to sustain the compressive load generated from drill string. • Piston breakage is minimum as it guided with inner cylinder where there will be even amount of air flow. • Air distributor distributes air to cylinder ports and controls air flow. JDC Series Air Consumption DESIGN HIGHLIGHTS EXCLUSIVE FEATURES APPLICATIONS

37. 37 DTH PRODUCT CATALOGUE STUNNER SERIES - 3.0” ST25BR - 3.5” ST30BR • Stunner Series is a valve type hammers designed for high performance at low operating air pressures. • Suitable bits has a strong robust design without foot valve to withstand heavy duty application. • Stunner Series Hammers maximizes energy output and reduces service requirements. • Wear Sleeve is not reversible. • All critical internal components are heat treated under strict control to maximize tool longevity. • Water Well • Mining • Construction • Quarry • Flapper mechanism helps to adjust inflow air pressure and it is guided with valve centralizer for correct positioning/movement of flapper valve. • Split bush used for guiding the bit and it provided with a groove for easy removal. • Inner cylinder guides piston and supplies air into piston area where the air flow is controlled. Stunner Series Air Consumption DESIGN HIGHLIGHTS EXCLUSIVE FEATURES APPLICATIONS

58. 58 DTH PRODUCT CATALOGUE FD SERIES - 4.5" FDS47DI - 7.0" FDS70DI - 8.0" FD80FD • FD Series is a valve less type hammers designed for high performance at low operating air pressures. • Suitable bits has a strong robust design without foot valve to withstand heavy duty application. • FD Series Hammers maximizes energy output and reduces service requirements. • Wear Sleeve is reversible except FDS47DI • All critical internal components are heat treated under strict control to maximize tool longevity. • Control tube sub assembly is used for guiding piston which minimizes the service requirements. • Hammer is inbuilt with buffer ring which will sustain the compressive load generated from drill string. • Water Well • Mining • Construction • Quarry DESIGN HIGHLIGHTS EXCLUSIVE FEATURES APPLICATIONS FD Series Air Consumption

90. 90 DTH PRODUCT CATALOGUE MALE (PIN) FEMALE (BOX) mm Thickness mm mm 2 3/8 API REG 2 3/8 API REG 76 4 3000 63 14-0760430023AR/W 2 3/8 API REG 2 3/8 API REG 89 4 3000 65 14-0890430023AR/W 2 3/8 API REG 2 3/8 API REG 76 6.3 4000 63 14-0760640023AR/W 2 3/8 API REG 2 3/8 API REG 89 6.3 5000 65 14-0890650023AR/W 2 3/8 API IF 2 3/8 API IF 89 4 3000 65 14-0890430023IF/W 2 7/8 API REG 2 7/8 API REG 102 6.3 5000 75 14-1020650027AR/W 2 7/8 API IF 2 7/8 API IF 114 6.3 5000 95 14-1140650031IF/W 3 1/2 API REG 3 1/2 API REG 114 6.3 5000 95 14-1140650031AR/W 2 3/8 API REG 2 3/8 API REG 73 5.16 3000 63 14-0730530023AR/W 5D KOREAN 5D KOREAN 73 5.16 1500 62.5 14-073051505DK/W 5D KOREAN 5D KOREAN 73 5.5 3000 62.5 14-073053005DK/W 7D KOREAN 7D KOREAN 73 5.5 1500 56 14-073051507DK/W 2 3/8 API REG 2 3/8 API REG 73 5.16 2000 63 14-0730520023AR/W 5D KOREAN 5D KOREAN 60.5 5.5 3000 62.5 14-060063005DK/W 7D KOREAN 7D KOREAN 60.5 5.5 1500 56 14-060063007DK/W THREAD FOR PIPE THREAD FOR PIPE DIA WALL LENGTH FLAT PRODUCT NO PIN - BOX DRILL PIPES 114.3 8 76 129 93 DHD3.5 139.7 5 116 160 127 DHD340 10 100 116 152.4 5.5 126 170 139 DHD340 168.3 5.5 142 190 155 DHD350 12.7 123 141 177.8 7 131 200 150 DHD350 / DHD360 / QL60 12.7 153 162 193.7 5.5 147 220 166 DHD360 / QL60 12.7 167 180 OD Casing Casing Wall Thickness ID Ring OD Ring Pilot Dia Shank DTH SYMMETRIC BITS

18. 18 DTH PRODUCT CATALOGUE BR33 MM Inch Outer Front KG LBS 90 3 1/2 2 12X7 11X5 4.6 10.2 36-42652090S 95 3 3/4 2 12X7 12X6 4.9 10.8 36-42663095S 100 3 15/16 2 14X8 12X6 5.3 11.6 36-42967100S 102 4 2 14X8 12X6 5.6 12.3 36-42967102S 105 4 1/8 2 14X8 12X6 5.9 13.0 36-42967105S Diameter Flush Hole Buttons Dia x Qty Weight Product No FLAT FACE BR SHANKS MM Inch Outer Front KG LBS 90 3 1/2 2 12X7 11X5 4.5 10.0 36-42452090S 95 3 3/4 2 12X7 12X6 4.8 10.5 36-42463095B 100 3 15/16 2 14X8 12X6 5.3 11.7 36-42767100S 102 4 2 14X8 12X6 5.6 12.3 36-42767102S 102 4 2 13X8 12X6 5.6 12.2 36-42765102B 105 4 1/8 2 14X8 12X6 5.9 13.1 36-42767105S Diameter Flush Hole Buttons Dia x Qty Weight Product No CONCAVE MM Inch Outer Front KG LBS 90 3 1/2 2 12X7 12X5 4.5 9.9 36-42553090S 95 3 3/4 2 12X7 12X6 4.7 10.3 36-42563095B 100 3 15/16 2 14X8 12X6 5.4 11.8 36-42867100S 100 3 15/16 2 14X8 12X6 5.4 11.9 36-42867100B 102 4 2 14X8 12X6 5.5 12.1 36-42867102S Diameter Flush Hole Buttons Dia x Qty Weight Product No CONVEX

74. 74 DTH PRODUCT CATALOGUE RC SERIES - 4” RC4 - 5” RC5 - 5.5” RC55 - 5.0” FCR55 • Water Well • Mining • Construction • Quarry RC Series Air Consumption DESIGN HIGHLIGHTS EXCLUSIVE FEATURES APPLICATIONS • Maximum material recovery up to 98% . • Special heat-treated sample tubes offer superior wear resistance. • Variable sample tube bore sizes allows greater flexibility. • Return tube can be changed without stripping the Hammer and also makes clearing blockages quickly. • Delivers maximum drilling under water • Specialized heat-treatment hardening for critical components for maximum longevity. • High durability shank design with short length allows for great transfer of energy . • The return tube can be changed without stripping the Hammer, that’s one feature. This helps in the field as being able to take out the return tube also makes clearing blockages quickly, • Also having the return tube in two pieces should keep down the cost of replacing the bottom section which is the high wear areaVariable sample tube bore sizes allows great - er flexibility. • Having the bit shroud should also increase the percentage of sample return..

3. TABLE OF CONTENT ISO STANDARDS 5 BIT FACE STYLES 6 BUTTON SHAPES 6 FEATURES & BENEFITS 7 BIT SHANK IDENTIFICATION CHART 8 SD SHANKS 10 PANTHER SHANKS 14 BR SHANKS 16 MACH SHANKS 19 DHD SHANKS 22 QL SHANKS 27 RK SHANKS 30 OTHER SHANKS SERIES 31 DTH SHANKS OPERATION & MAINTENANCE 33 SHOCK ABSORBER 83 ODEX 86 ADAPTERS 89 DRILL PIPES 90 DTH SYMMETRIC SYSTEM 90 INTRODUCTION SPECIFICATION CHARTS 91 DTH SHANKS 10 DTH HAMMER SERIES 36 OTHER DTH PRODUCTS 82 STUNNER SERIES 37 WINNER SERIES 40 JDM SERIES 43 JDC SERIES 51 FD SERIES 58 D SERIES 62 DRT SERIES 67 UDC SERIES 70 RC SERIES 74 DTH HAMMERS MAINTENANCE 79

83. 83 DTH PRODUCT CATALOGUE SHOCK ABSORBER - 4” SHOCK ABSORBER - 5” SHOCK ABSORBER - 6” SHOCK ABSORBER - 8” SHOCK ABSORBER - 10” SHOCK ABSORBER • Innovative Design For Air And Water Well Application. • Increased Rate Of Penetration. • Drive Splines For More Better Torque Handling And Wear Resistance • DRT Series Hammers maximizes energy output and reduces service requirements. • Superior Shock Absorption. • Rig Top Drive Protection Through Hyper Absorption Technology. KEY FEATURES 4” SHOCK ABSORBER SL.NO NAME OF THE ITEM QTY PART NO 1 TOP CONNECTOR 1 91-SA4000-23ARM 2 RETAINER RING 1 99-SA4000 3 SPLINED NUT O RING 1 37-SA07203H 4 SPLINED NUT 1 92-SA4000 5 NUT SEALING RING 1 27-SA807406 6 BREAK OUT WASHER 1 29-SA4000 7 THRUST WASHER 1 93-SA4000 8 THRUST WASHER O RING 1 37-SA04002H 9 BUFFER RING 2 27-SA714626 10 BOTTOM CONNECTOR 1 94-SA4000-23ARF SHOCK ABSORBER ASSEMBLY 1 84-SA095-23ARMF A DEDICATED TOOL FOR 4.0” DRILLING SL.NO DESCRIPTION UNIT DIMENSION 1 OUSIDE DIAMETER MM 95.00 2 EFFECTIVE LENGTH MM 490.00 3 NET WEIGHT KG 23 HAMMER SPECIFICATION 3 6 7 4 8 1 5 2 9 10 OTHER DTH PRODUCTS

25. 25 DTH PRODUCT CATALOGUE MM Inch Outer Front KG LBS 127 5 2 14X8 14X7 14.5 32 36-53879127S 140 5 1/2 2 16X8 14X8 16.2 35.7 36-5388C140S 140 5 1/2 2 16X8 16X7 16.4 36 36-5387D140S 146 5 3/4 2 16X8 16X8 16.6 36.6 36-5388D146S 150 6 2 16X8 16X10 16.9 37.1 36-5380D150S Diameter Flush Hole Buttons Dia x Qty Weight Product No CONVEX MM Inch Outer Front KG LBS 152 6 2 16X8 16X10 23.9 52.7 36-6390D152S 156 6 1/8 2 16X8 16X10 24.1 53.2 36-6390D156S 165 6 1/2 3 16X9 16X10 26.7 58.8 36-63P0D165S 165 6 1/2 2 16X8 16X10 26.7 58.8 36-6390D165S 172 6 3/4 2 16X10 16X12 27.5 60.6 36-63K2D172S 178 7 2 18X10 16X12 28 61.7 36-63K2E178S 180 7 1/8 2 16X10 16X13 28.2 62.2 36-63KED180S 185 7 2/7 2 16X10 16X13 29.1 64.0 36-63KED185S 190 7 1/2 2 18X10 16X13 30.1 66.4 36-63KEE190S 200 7 7/8 2 16X10 16X14 32.1 70.7 36-63KFD200S 203 8 2 18X10 16X16 32.7 72.0 36-63KHE203S 203 8 2 16X10 16X16 32.7 72.0 36-63KHD203S 216 8 1/2 2 19X10 16X16 33.1 72.9 36-63KHI216S 216 8 1/2 3 19X9 16X18 33.1 72.9 36-63PII216S 220 8 5/8 2 19X10 16X16 33.8 74.4 36-63KHI220S 220 8 2/3 2 19X10 16X18 33.6 74.0 36-63KII220S 225 8 6/7 2 19X10 16X18 34.1 75.1 36-63KII225S 250 9 5/6 3 19X12 16X22 35.2 77.6 36-63SII250S 254 10 3 18X12 16X24 35.9 79.0 36-63SIE254S 300 11 4/5 2 18X12 16X27 36.8 81.1 36-63MJE300S Diameter Flush Hole Buttons Dia x Qty Weight Product No FLAT FACE MM Inch Outer Front KG LBS 152 6 2 16X8 16X10 23.6 52.1 36-6370D152S 154 6 2 16X8 16X10 23.8 52.4 36-6370D154S 165 6 1/2 2 16X10 16X10 24.1 53.2 36-63I0D165P 165 6 1/2 2 16X10 16X10 24.1 53.2 36-63I0D165S 165 6 1/2 3 18X9 16X10 24.7 54.5 36-63N0E165S 170 6 2/3 2 19X8 16X11 25.8 56.8 36-6371I170S 171 6 3/4 2 16X10 16X13 26.0 57.3 36-63IED171S 172 6 7/9 2 16X10 16X14 26.2 57.7 36-63IFD172S 178 7 2 16X10 16X12 26.7 58.9 36-63I2D178S 178 7 2 16X8 16X10 27.1 59.6 36-6370D178S 180 7 2 16X10 16X12 26.5 58.3 36-63I2D180S 185 7 2/7 2 16X10 16X16 26.4 58.1 36-63IHD185S 190 7 1/2 2 16X10 16X16 29.8 65.8 36-63IHD190S 192 7 5/9 2 18X10 16X14 30.0 66.1 36-63IFE192S 200 7 7/8 2 16X10 16X16 30.8 68.0 36-63IHD200S 203 8 2 19X10 16X16 31.2 68.8 36-63IHI203S 203 8 3 18X9 16X15 31.2 68.8 36-63NGE203S 216 8 1/2 2 19X10 16X16 32.3 71.2 36-63IHI216S 220 8 5/8 2 19X10 16X16 32.4 71.4 36-63IHI220S 240 9 4/9 3 19X12 16X24 34.2 75.3 36-63QII240S 254 10 3 18X12 16X20 36.2 79.8 36-63QIE254S Diameter Flush Hole Buttons Dia x Qty Weight Product No CONCAVE DHD360 DHD SHANKS

79. 79 DTH PRODUCT CATALOGUE • All rods should be cleaned before use to remove scrap (sometimes found in new rods), rust scales and debris. • Ensure that the air screen is in place and free from obstruction. • If hammer oil is only added at each rod change, care should be taken to ensure that an adequate supply of oil is maintained to the hammer at the recommended rate. Therefore, in hard formations, it may be necessary to add oil between rod changes. GENERAL INSTRUCTIONS As a guide to the most efficient weight the following procedure should be used. • Increase down-pressure until air pressure ceases to increase. • Note hydraulic feed pressure. • Reduce down the pressure until air pressure starts to decrease and note hydraulic feed pressure. • Operate between these two settings. Before shutting down at the end of each shift, we recommend the following procedures. • Flush hammer with air/water for few minutes and then turn off water injection. • Flush hammer with air/oil for a few minutes. This will coat the hammer parts preventing corrosion/rust. • Never leave the tool in a wet/muddy hole. Pull back from bottom as far as necessary to prevent the hammer sitting under water. • It is also good practice to pour at least half litre of oil down the drill at start-up of new shift. • If the hammer is removed from the drill rig for any reason, it is wise to pour some quantity of oil into it and • Pipe wrenches with flat jaws are not recommended as break-out tools. A more suitable tool would be a chain wrench, or similar type tool, which encircles the circumferences of cylinder (pipe wrenches with radial jaws approximating the curvature of the cylinder are also acceptable). • It is not recommended to use heat on any part of the hammer to assist break-ot,as this will affect the structure of the steel. • It is not recommended to subject the hammer to any external impact to assist break-out, as deformation of the cylinder and damage to threads may occur. • Break-out tool placement should not be over the cylinder thread area as this can lead to distortion and ultimate breakage. • Break-out tool placement on the bit shank is not recommended as this will damage the lower seal area. This will cause misalignment of the bit in the drive sub It is extremely important that an adequate supply of the correct type of rock drill oil is constantly fed to the ham - mer whilst it is operating. Failure to do so will quickly lead to excessive component wear and if the oil supply is cut off for any reason, the piston will quickly seize inside the wearsleeve, resulting in irreparable damage to both components. An airline lubrication system should be installed, preferable on the drill rig. The lubricator reservoir should be of sufficient capacity to supply the required volume of rock drill oil for a full shift. With this hammer, this might prove impractical, but the capacity should be sufficient for at least half a shift.This is equally important that the lubricator system must be adjustable and have a visual check to ensure the lubricator does not run out of oil. The amount of lubricating oil should be increased by 50% when drilling with water or foam. When new drill pipes are added to the drill string, it is recommended that a half pint (quarter of a litre) of rock drill oil is poured into the pipe to provide a good internal coating and helps prevent the hammer from running dry at any time. The grade of rock drill oil will be determined by the ambient temperature at the drilling site. If the ambient temperature is between 0 and 25 degree centigrade, then 30 grade oil should be used. If the ambient temperature is greater than 25 degree centigrade, use 50 grade oil. • As a rule of thumb, rotate the bit 2 revolutions per inch (25.4mm) of penetration. • Rotation too slow or too fast can cause premature bit failure. DTH HAMMERS MAINTENANCE GENERAL CARE RECOMMENDED WEIGHT ON THE BIT / ROTATION SPEEDS SHUT DOWN LUBRICATION HAMMER BREAKOUT block both ends. Provided the flushing, as outlined in steps one and two above have been carried out, the hammer should be stripped, cleaned and oiled before being stored.

81. 81 DTH PRODUCT CATALOGUE • There are two main areas to examine on a used piston:- • Check the body diameter for signs of pick-up and burning (both are signs of poor lubrication). Using a micrometer measure the diameter and refer to the quoted minimum size above. • Any light ‘Pick up’ marks can be removed using emery cloth, however if there are signs of overheating and cracking the piston should be replaced and the lubrication system examined. • Secondly, using a micrometer, measure the diameter of the bore at both ends of the piston andrefer to the maximum quoted sizes. • Examine the striking face. Some degree of distortion is acceptable providing there are no signs of cracking. If distortion has affected the chamfer and possibly distorted the foot valve bore diameter, this needs to be reformed on a lathe and the foot valve bore re-ground to its original diameter. Burrs and dents can be removed with an emery stone. INSPECTION • Either a micrometer or a vernier, measure the outer diameter of the wear sleeve. If it is below the minimum it must be replaced. The wear rate of the wear sleeve can be slowed by replacing the chuck before the wear area reaches the wear sleeve. • The bore of the wear sleeve should be periodically checked for any signs of ‘pick-up’. If a piston has broken within the wear sleeve it is imperative that the bore is honed to remove any burrs or ‘pick-up’. Failure to do so will result in ‘pick-up’ on the replaced piston and will lead to early failure of this component. • Inspect the O.D. for nicks, burrs and scoring. • Remove all minor irregularities with emery cloth. • Replace if necessary. AIR DISTRIBUTOR • The check valve should be smooth and free from abrasions. Replace if necessary. CHECK VALVE • Check make-up face, removing all nicks and marks. • Remove all burrs on the thread area with a fine file. • Inspect for damage such as cracks and deformations. • Replace if necessary. BACK HEAD O RINGS CHUCK DTH HAMMERS MAINTENANCE PISTON WEAR SLEEVE • Check for wear and cracks. • Always try and keep the chuck diameter should not be small than the wear sleeve this extends the service life of the wear sleeve.

84. 84 DTH PRODUCT CATALOGUE SHOCK ABSORBER 5”SHOCK ABSORBER SL.NO NAME OF THE ITEM QTY PART NO 1 TOP CONNECTOR 1 91-SA5000-31ARM 2 RETAINER RING 1 99-SA5000 3 SPLINED NUT O RING 1 37-SA8803H 4 SPLINED NUT 1 92-SA5000 5 NUT SEALING RING 1 27-SA989011 6 BREAK OUT WASHER 1 29-SA5000 7 THRUST WASHER 1 93-SA5000 8 THRUST WASHER O RING 1 37-SA4703H 9 BUFFER RING 2 27-SA895943 10 BOTTOM CONNECTOR 1 94-SA5000-31ARF SHOCK ABSORBER ASSEMBLY 1 84-SA114-23ARMF A DEDICATED TOOL FOR 5.0” DRILLING SL.NO DESCRIPTION UNIT DIMENSION 1 OUSIDE DIAMETER MM 114.30 2 EFFECTIVE LENGTH MM 525.00 3 NET WEIGHT KG 36 HAMMER SPECIFICATION SL.NO NAME OF THE ITEM QTY PART NO 1 TOP CONNECTOR 1 91-SA6000-31ARM 2 SPLINED NUT O RING 2 37-SA1003H 3 SPLINED NUT 1 92-SA6000 4 SPLINED NUT SEAL 1 27-SA111112 5 BREAK OUT WASHER 1 29-SA6000 6 RETAINER RING 1 99-SA6000 7 THRUST WASHER 1 93-SA6000 8 THRUST WASHER O RING 1 37-SA5305H 9 BUFFER RING 2 27-SA116557 10 BOTTOM CONNECTOR 1 94-SA6000-31ARF SHOCK ABSORBER ASSEMBLY 1 84-SA140-31ARMF A DEDICATED TOOL FOR 6.0” DRILLING SL.NO DESCRIPTION UNIT DIMENSION 1 OUSIDE DIAMETER MM 140 2 EFFECTIVE LENGTH MM 585.00 3 NET WEIGHT KG 53 HAMMER SPECIFICATION 6”SHOCK ABSORBER 3 6 7 4 9 1 5 2 10 8 3 6 7 4 8 1 5 2 9 10

88. 88 DTH PRODUCT CATALOGUE DEEPEX 190 (DX190DHW) PART DESCRIPTION PRODUCT NUMBER DX190DHW DEEPEX ASSEMBLY 26-63190R237EW GUIDE DEVICE SHANK DHD 360 SHANK G6-63190R237EW PILOT BIT 190 mm DIA P6-190R237EW REAMER BIT 237 mm DIA R6-190R237EW CASING SHOE PIPE 222/205 MM S6-190EW DEEPEX 190 (DX190SDW) PART DESCRIPTION PRODUCT NUMBER DX190SDW DEEPEX ASSEMBLY 26-61190R237EW GUIDE DEVICE SHANK SD6 SHANK G6-61190R237EW PILOT BIT 190 mm DIA P6-190R237EW REAMER BIT 237 mm DIA R6-190R237EW CASING SHOE PIPE 222/205 MM S6-190EW ODEX DEEPEX 190 (DX190QLW) PART DESCRIPTION PRODUCT NUMBER DX190QLW DEEPEX ASSEMBLY 26-65190R237EW GUIDE DEVICE SHANK QL60 SHANK G6-65190R237EW PILOT BIT 190 mm DIA P6-190R237EW REAMER BIT 237 mm DIA R6-190R237EW CASING SHOE PIPE 222/205 MM S6-190EW DEEPEX 240 (DX240DHW) PART DESCRIPTION PRODUCT NUMBER DX240DHW DEEPEX ASSEMBLY 26-83240R306FW GUIDE DEVICE SHANK DHD380 SHANK G6-83240R306FW PILOT BIT 240 mm DIA P6-240R3067FW REAMER BIT 306 mm DIA R6-240R306FW CASING SHOE PIPE 273/260 MM S6-240FW DEEPEX 240 (DX240QLW) PART DESCRIPTION PRODUCT NUMBER DX240QLW DEEPEX ASSEMBLY 26-85240R306FW GUIDE DEVICE SHANK QL80SHANK G6-85240R306FW PILOT BIT 240 mm DIA P6-240R306FW REAMER BIT 306 mm DIA R6-240R306FW CASING SHOE PIPE 273/260 MM S6-240FW DEEPEX 240 (DX240RKW) PART DESCRIPTION PRODUCT NUMBER DX240QLW DEEPEX ASSEMBLY 26-R1240R306FW GUIDE DEVICE SHANK RK1SHANK G6-R1240R306FW PILOT BIT 240 mm DIA P6-240R306FW REAMER BIT 306 mm DIA R6-240R306FW CASING SHOE PIPE 273/260 MM S6-240FW

13. 13 DTH PRODUCT CATALOGUE SD8 Diameter Flush Hole Buttons Dia x Qty Weight Product No CONCAVE SD10 MM Inch Outer Front KG LBS 254 10 2 19X12 16X24 81.5 179.7 36-S1LII254S 270 10 5/8 3 19X12 16X25 87.8 193.5 36-S1QII270S 280 11 3 19X12 16X27 90.3 199.1 36-S1QJI280S 292 11 1/2 3 19X21 16X23 91.6 201.9 36-S1UII292S 305 12 3 19X18 19X15 97.6 215.1 36-S1UJI305S 16X13 330 13 3 19X18 19X18 102.7 226.4 36-S1UJI330S 16X13 Diameter Flush Hole Buttons Dia x Qty Weight Product No CONCAVE SD12 MM Inch Outer Front KG LBS 305 12 3 19x12 16x27 123.1 271.4 36-S2SJI305S Diameter Flush Hole Buttons Dia x Qty Weight Product No FLAT FACE SD SHANKS MM Inch Outer Front KG LBS 200 7 7/8 2 19X10 16X15 43.5 95.8 36-81IGI200S 203 8 3 19X9 19X6 43.8 96.5 36-81NGI203S 16X9 216 8 1/2 2 19X10 16X16 43.4 95.6 36-81IHI216S 216 8 1/2 3 19X12 19X6 44.5 98.1 36-81QHI216S 16X10 222 8 3/4 2 19X10 16X16 47.0 103.6 36-81IHI222S 241 9 1/2 2 19X10 16X19 50.5 111.3 36-81III241S 251 9 7/8 2 19X10 16X20 51.0 112.4 36-81III251S 254 10 2 19X10 16X20 51.4 113.4 36-81III254S 270 10 5/8 3 19X12 16X25 57.1 126.0 36-81QII270S 280 11 3 19X12 16X30 59.3 130.8 36-81QJI280S 305 12 3 19x18 19X15 70.9 156.4 36-81UJI305S 16X13 311 12 1/4 3 19X12 19X21 73.7 162.5 36-81QJI311S 16X9

85. 85 DTH PRODUCT CATALOGUE SHOCK ABSORBER 8”SHOCK ABSORBER SL.NO NAME OF THE ITEM QTY PART NO 1 TOP CONNECTOR 1 91-SA8000-41ARM 2 BUFFER RING 1 27-SA159258 3 THRUST WASHER 1 93-SA8000 4 SPLINED NUT O RING 1 37-SA1503H 5 SPLINED NUT 1 92-SA8000 6 BREAKER OUT WASHER 1 29-SA8000 7 SHAFT 1 96-SA8000 8 SHAFT O-RING 1 37-SA11604H 9 BOTTOM CONNECTOR 1 94-SA8000-41ARF SHOCK ABSORBER ASSEMBLY 1 84-SA178-41ARMF A DEDICATED TOOL FOR 8.0” DRILLING SL.NO DESCRIPTION UNIT DIMENSION 1 OUSIDE DIAMETER MM 178.00 2 EFFECTIVE LENGTH MM 600.00 3 NET WEIGHT KG 84 HAMMER SPECIFICATION SL.NO NAME OF THE ITEM QTY PART NO 1 TOP CONNECTOR 1 91-SA10000-65ARM 2 BUFFER RING 1 27-SA181357 3 BREAKER OUT WASHER 1 29-SA10000 4 SHAFT O-RING 1 37-SA15504H 5 SHAFT 1 96-SA10000 6 SPLINED NUT ORING 1 37-SA9503H 7 SPLINED NUT 1 92-SA10000 8 THRUST WASHER 1 93-SA10000 9 BOTTOM CONNECTOR 1 94-SA10000-65ARF SHOCK ABSORBER ASSEMBLY 1 84-SA215-65ARMF A DEDICATED TOOL FOR 10.0” DRILLING SL.NO DESCRIPTION UNIT DIMENSION 1 OUSIDE DIAMETER MM 216.0 2 EFFECTIVE LENGTH MM 654.0 3 NET WEIGHT KG 98.0 HAMMER SPECIFICATION 10”SHOCK ABSORBER 3 6 7 4 8 1 5 2 9 3 6 7 4 8 1 5 2 9

87. 87 DTH PRODUCT CATALOGUE DEEPEX 140 (DX140DHW) PART DESCRIPTION PRODUCT NUMBER DX140DHW DEEPEX ASSEMBLY 26-53140R181CW GUIDE DEVICE SHANK DHD350 SHANK G6-53140R181CW PILOT BIT 140 mm DIA P6-140R181CW REAMER BIT 181 mm DIA R6-140R181CW CASING SHOE 171/157 MM S6-140CW DEEPEX 140 (DX140D4W) PART DESCRIPTION PRODUCT NUMBER DX140D4W DEEPEX ASSEMBLY 26-56140R181CW GUIDE DEVICE SHANK D4 SHANK G6-56140R181CW PILOT BIT 140 mm DIA P6-140R181CW REAMER BIT 181 mm DIA R6-140R181CW CASING SHOE 171/157 MM S6-140CW DEEPEX 140 (DX140QLW) PART DESCRIPTION PRODUCT NUMBER DX140QLW DEEPEX ASSEMBLY 26-55140R181CW GUIDE DEVICE SHANK QL50 SHANK G6-55140R181CW PILOT BIT 140 mm DIA P6-140R181CW REAMER BIT 181 mm DIA R6-140R181CW CASING SHOE 171/157 MM S6-140CW ODEX DEEPEX 165 (DX165DHW) PART DESCRIPTION PRODUCT NUMBER DX165DHW DEEPEX ASSEMBLY 26-63165R209DW GUIDE DEVICE SHANK DHD360 SHANK G6-63165R209DW PILOT BIT 165 mm DIA P6-165R209DW REAMER BIT 209 mm DIA R6-165R209DW CASING SHOE 196/183 MM S6-165DW DEEPEX 165 (DX165SDW) PART DESCRIPTION PRODUCT NUMBER DX165SDW DEEPEX ASSEMBLY 26-61165R209DW GUIDE DEVICE SHANK SD6 SHANK G6-61165R209DW PILOT BIT 165 mm DIA P6-165R209DW REAMER BIT 209 mm DIA R6-165R209DW CASING SHOE 196/183 MM S6-165DW PART DESCRIPTION PRODUCT NUMBER DX165QLW DEEPEX ASSEMBLY 26-65165R209DW GUIDE DEVICE SHANK QL60 SHANK G6-65165R209DW PILOT BIT 165 mm DIA P6-165R209DW REAMER BIT 209 mm DIA R6-165R209DW CASING SHOE PIPE 196/183 MM S6-165DW DEEPEX 165 (DX165QLW)

89. 89 DTH PRODUCT CATALOGUE mm mm mm A/F Width 2 3/8 API REG BOX 2 3/8 API REG BOX 28 89 250 70 40 24-B17B17089250070 2 3/8 API REG BOX 2 7/8 API IF BOX 32 114 280 90 50 24-B17B20114280090 2 3/8 API REG BOX 3 1/2 API REG BOX 32 114 280 70 50 24-B17B21114280070 2 7/8 API IF BOX 2 7/8 API IF BOX 38 114 310 90 50 24-B20B20114310090 2 7/8 API IF BOX 3 1/2 API REG BOX 38 114 310 90 50 24-B18B21114310090 2 3/8 API REG BOX 2 3/8 API IF BOX 30 89 260 70 40 24-B17B18089260070 2 3/8 API IF BOX 3 1/2 API REG BOX 38 114 310 90 50 24-B18B21114310090 2 3/8 API IF BOX 4 1/2 API REG BOX 38 140 330 90 50 24-B18B24140330090 3 1/2 API REG BOX 3 1/2 API IF BOX 36 130 330 90 50 24-B21B23130330090 4 1/2 API REG BOX 3 1/2 API IF BOX 45 140 360 90 50 24-B24B23140360090 CONNECTION A CONNECTION B INNER DIA DIA LENGTH WRENCH Product No BOX - BOX mm mm mm A/F Width 2 3/8 API REG PIN 2 7/8 API IF PIN 32 114 280 90 50 24-P17P20114280090 2 7/8 API IF PIN 3 1/2 API REG PIN 38 114 300 90 50 24-P20P21114300090 2 7/8 API IF PIN 2 7/8 API IF PIN 38 114 300 90 50 24-P20P20114300090 2 3/8 API REG PIN 3 1/2 API REG PIN 32 114 280 90 50 24-P17P21114280090 2 3/8 API REG PIN 2 3/8 API REG PIN 28 89 240 70 40 24-P17P17089240070 2 3/8 API REG PIN 2 3/8 API REG PIN 28 76 240 54 40 24-P17P17076240054 2 3/8 API IF PIN 3 1/2 API REG PIN 38 114 280 90 50 24-P18P21114280090 3 1/2 API REG PIN 3 1/2 API REG PIN 38 114 320 90 50 24-P21P21114320090 4 1/2 AP1 REG PIN 3 1/2 API REG PIN 45 140 360 90 50 24-P24P21140360090 4 1/2 API REG PIN 4 1/2 API REG PIN 45 140 400 90 50 24-P24P24140400090 CONNECTION A CONNECTION B INNER DIA DIA LENGTH WRENCH Product No PIN - PIN mm min max mm A/F Width 2 3/8 API REG PIN 2 3/8 API REG BOX 28 89 89 250 70 40 24-P17B17089250070 3 1/2 API IF PIN 6 5/8 API REG BOX 45 160 180 400 115 50 24-P23B27180400115 3 1/2 API IF PIN 4 1/2 API REG BOX 45 120 140 350 90 50 24-P23B24140350090 3 1/2 API REG PIN 6 5/8 API REG BOX 40 160 180 400 115 50 24-P21B27180400115 3 1/2 API REG PIN D17 BOX 38 114 140 330 90 50 24-P21B30140330090 3 1/2 API REG PIN 3 1/2 API REG BOX 38 114 114 300 90 50 24-P21B21114300090 3 1/2 API REG PIN 2 7/8 API IF BOX 38 114 114 310 90 50 24-P21B20114310090 3 1/2 API REG PIN 2 3/8 API REG BOX 32 114 114 280 90 50 24-P21B17114280090 2 7/8 API IF PIN D17 BOX 38 114 140 330 90 50 24-P20B30140330090 2 7/8 API IF PIN 4 1/2 API REG BOX 38 114 148 330 90 50 24-P20B24148330090 2 7/8 API IF PIN 3 1/2 API REG BOX 38 114 114 300 90 50 24-P20B21114300090 2 7/8 API IF PIN 2 7/8 API IF BOX 38 114 114 300 90 50 24-P20B20114300090 2 7/8 API IF PIN 2 3/8 API REG BOX 32 114 114 280 90 50 24-P20B17114280090 2 7/8 API REG PIN 3 1/2 API REG BOX 30 89 114 300 70 40 24-P19B21114300070 2 7/8 API REG PIN 2 7/8 API IF BOX 30 89 114 300 70 40 24-P19B20114300070 2 7/8 API REG PIN 2 3/8 API REG BOX 30 89 89 260 70 40 24-P19B17089260070 2 3/8 API IF PIN 2 3/8 API IF BOX 38 89 89 280 65 40 24-P18B18089280065 2 3/8 API REG PIN 3 1/2 API REG BOX 32 114 114 280 90 50 24-P17B21114280090 2 7/8 API IF PIN 6 5/8 API REG BOX 40 160 180 400 115 50 24-P20B27180400115 3 1/2 API IF PIN D17 BOX 50 140 140 331 115 50 24-P23B30140331115 3 1/2 API REG BOX 3 1/2 API IF PIN 36 130 130 330 90 60 24-B21P23130330090 6 5/8 API REG BOX 4 1/2 API REG PIN 40 150 195 383 115 50 24-B24P27195383115 4 1/2 API REG BOX 4 1/2 API REG PIN 45 114 140 400 90 50 24-B24P24140400090 4 1/2 API REG PIN 3 1/2 API REG BOX 45 140 140 360 90 50 24-P24B21140360090 4 1/2 API REG PIN D17 BOX 40 140 140 330 100 50 24-P24B30140330100 CONNECTION A CONNECTION B INNER DIA DIA (mm) LENGTH WRENCH Product No PIN - BOX ADAPTERS

86. 86 DTH PRODUCT CATALOGUE PART DESCRIPTION PRODUCT NUMBER DX90DHW DEEPEX ASSEMBLY 26-33090R123AW GUIDE DEVICE SHANK DHD3.5 SHANK G6-33090R123AW PILOT BIT 90 mm DIA P6-090R123AW REAMER BIT 123 mm DIA R6-090R123AW CASING SHOE PIPE 115/102 MM S6-090AW PILOT BIT REAMER CASING SHOE GUIDE DEVICE DEEPEX 115 (DX115DHW) PART DESCRIPTION PRODUCT NUMBER DX115DHW DEEPEX ASSEMBLY 26-43115R152BW GUIDE DEVICE SHANK DHD340 SHANK G6-43115R152BW PILOT BIT 115 mm DIA P6-115R152BW REAMER BIT 152 mm DIA R6-115R152BW CASING SHOE PIPE 142/128 MM S6-115BW DEEPEX 115 (DX115QLW) PART DESCRIPTION PRODUCT NUMBER DX115QLW DEEPEX ASSEMBLY 26-45115R152BW GUIDE DEVICE SHANK QL40 SHANK G6-45115R152BW PILOT BIT 115 mm DIA P6-115R152BW REAMER BIT 152 mm DIA R6-115R152BW CASING SHOE PIPE 142/128 MM S6-115BW ODEX DEEPEX 115 (DX115MXW) PART DESCRIPTION PRODUCT NUMBER DX115MXW DEEPEX ASSEMBLY 26-44115R152BW GUIDE DEVICE SHANK MX4 SHANK G6-44115R152BW PILOT BIT 115 mm DIA P6-115R152BW REAMER BIT 152 mm DIA R6-115R152BW CASING SHOE PIPE 142/128 MM S6-115BW DEEPEX 115 (DX115PAW) PART DESCRIPTION PRODUCT NUMBER DX115PAW DEEPEX ASSEMBLY 26-47115R152BW GUIDE DEVICE SHANK PANTHER SHANK G6-47115R152BW PILOT BIT 115 mm DIA P6-115R152BW REAMER BIT 152 mm DIA R6-115R152BW CASING SHOE PIPE 142/128 MM S6-115BW DEEPEX 90 (DX90DHW)

12. 12 DTH PRODUCT CATALOGUE SD6 MM Inch Outer Front KG LBS 152 6 2 16X8 16X10 26.3 58.0 36-6190D152S 156 6 1/8 2 16X8 16X10 26.5 58.4 36-6190D156S 165 6 1/2 3 16X9 16X10 28.8 63.4 36-61P0D165S 172 6 3/4 3 16X9 16X10 29.0 63.9 36-61P0D172S 178 7 2 16X10 16X13 29.5 65.1 36-61KED178S 190 7 1/2 2 16X10 16X14 31.9 70.2 36-61KFD190S 200 7 7/8 2 16X10 16X14 33.1 73.0 36-61KFD200S 203 8 2 19X10 16X16 33.6 74.1 36-61KHI203S 216 8 1/2 2 19X10 16X16 35.9 79.3 36-61KHI216S 216 8 1/2 2 18X10 16X16 36.0 79.4 36-61KHE216S 254 10 2 19X10 16X20 43.1 95.0 36-61KII254S Diameter Flush Hole Buttons Dia x Qty Weight Product No FLAT FACE MM Inch Outer Front KG LBS 152 6 2 16X8 16X10 26.1 57.4 36-6170D152S 165 6 1/2 2 16X10 16X10 27.9 61.4 36-61I0D165S 172 6 3/4 2 16X10 16X11 28.8 63.4 36-61I1D172S 178 7 3 16X9 16X12 29.4 64.9 36-61N2D178S 190 7 1/2 2 16X10 16X14 31.8 70.0 36-61IFD190S 203 8 2 19X10 16X16 33.1 73.0 36-61IHI203S 216 8 1/2 2 19X10 16X16 34.8 76.6 36-61IHI216S 219 8 5/8 2 19X10 16X16 35.1 77.3 36-61IHI219S 219 8 5/8 2 19X10 16X17 35.1 77.4 36-61III219S Diameter Flush Hole Buttons Dia x Qty Weight Product No CONCAVE MM Inch Outer Front KG LBS 152 6 2 16X8 16X10 26.0 57.3 36-6180D152S 165 6 1/2 2 16X10 16X10 27.7 61.1 36-61J0D165S 172 6 3/4 3 16X12 16X10 28.5 62.8 36-61R0D172S Diameter Flush Hole Buttons Dia x Qty Weight Product No CONVEX SD8 MM Inch Outer Front KG LBS 200 7 7/8 2 19X10 16X15 43.7 96.3 36-81KGI200S 203 8 2 19X10 16X16 44.1 97.1 36-81KHI203S 203 8 3 19X9 19X6 44.3 97.6 36-81PGI203S 16X9 216 8 1/2 2 19X10 16X16 44.5 98.1 36-81KHI216S 219 8 5/8 2 19X10 16X16 45.6 100.6 36-81KHI219S 222 8 3/4 2 19X10 16X18 45.8 100.9 36-81KII222S 225 8 7/8 2 19X10 16X20 46.5 102.5 36-81KII225S 240 9 4/9 2 19X10 16X20 50.0 110.1 36-81KII240S 241 9 1/2 2 19X10 16X20 50.0 110.1 36-81KII241S 250 9 5/6 2 19X10 16X20 52.5 115.7 36-81KII250S 254 10 2 19X10 16X20 53.5 117.9 36-81KII254S 292 11 1/2 3 19X12 16X30 61.3 135.0 36-81SJI292S 300 11 4/5 3 19X12 16X27 62.2 137.1 36-81SJI300S Diameter Flush Hole Buttons Dia x Qty Weight Product No FLAT FACE SD SHANKS

26. 26 DTH PRODUCT CATALOGUE DHD380 MM Inch Outer Front KG LBS 203 8 2 19X10 16X15 49.7 109.6 36-83KGI203S 203 8 2 19X12 16X15 49.8 109.8 36-83MGI203S 216 8 1/2 2 19X10 16X16 50.7 111.8 36-83KHI216S 219 8 5/8 2 19X10 16X16 51.3 113.1 36-83KHI219S 220 8 5/8 2 19X12 16X16 51.9 114.4 36-83MHI220S 222 8 3/4 2 19X10 16X16 52.9 116.6 36-83KHI222S 225 8 7/8 2 19X10 16X14 53.7 118.3 36-83KFI225S 240 9 4/9 2 19X10 16X20 57.6 126.9 36-83KII240S 241 9 1/2 2 19X10 16X19 57.7 127.1 36-83KII241S 250 9 5/6 2 19X10 16X20 61.5 135.6 36-83KII250S 254 10 2 19x12 16x24 62.2 137.2 36-83MII254S 292 11 1/2 3 19X12 16X30 70.3 155.0 36-83SJI292S 300 11 4/5 3 19X12 16X27 71.5 157.5 36-83SJI300S 305 12 3 19X12 16X27 71.9 158.5 36-83SJI305S 311 12 1/4 3 19X12 16X30 72.7 160.3 36-83SJI311S Diameter Flush Hole Buttons Dia x Qty Weight Product No FLAT FACE MM Inch Outer Front KG LBS 198 7 4/5 2 16X12 16X19 49.5 109.2 36-83LID198S 200 7 7/8 2 16X12 16X19 50.7 111.8 36-83LID200S 203 8 2 19X10 16X16 51.4 113.3 36-83IHI203S 216 8 1/2 2 19X10 16X16 52.0 114.5 36-83IHI216S 219 8 5/8 2 19X10 16X16 52.5 115.7 36-83IHI219S 229 9 2 16X10 16X18 53.8 118.6 36-83IID229S 241 9 1/2 2 19X10 16X19 55.1 121.6 36-83III241S 254 10 2 19x10 16x20 58.3 128.5 36-83III254S 267 10 1/2 3 19X12 16X25 62.5 137.8 36-83QII267S 280 11 3 19X12 16X30 65.9 145.2 36-83QJI280S 281 11 3 19X12 16X26 66.3 146.2 36-83QJI281S 300 11 4/5 3 19X18 16X24 71.9 158.4 36-83UII300S 305 12 3 19x18 19X15 74.0 163.1 36-83UJI305S 16X13 Diameter Flush Hole Buttons Dia x Qty Weight Product No CONCAVE MM Inch Outer Front KG LBS 300 11 4/5 3 19x12 19X9 72.2 159.2 36-83RJI300S 16X21 Diameter Flush Hole Buttons Dia x Qty Weight Product No CONVEX DHD SHANKS MM Inch Outer Front KG LBS 165 6 1/2 3 18X9 16X12 24.7 54.3 36-63O2E165B 172 6 7/9 3 16X12 16x10 25.5 56.2 36-63R0D172S 203 8 3 16X9 16X16 29.8 65.7 36-63OHD203S 216 8 1/2 3 19X9 16X18 31.0 68.2 36-63OII216S 250 9 5/6 3 19X12 19X18 34.3 75.6 36-63RIJ250S Diameter Flush Hole Buttons Dia x Qty Weight Product No CONVEX

29. 29 DTH PRODUCT CATALOGUE QL60 MM Inch Outer Front KG LBS 152 6 2 16X8 16X9 23.7 52.1 36-6599D152S 165 6 1/2 3 16X9 16X10 24.9 54.9 36-65P0D165S 165 6 1/2 2 19X8 16X10 25.3 55.8 36-6590I165S 165 6 1/2 2 16X10 16X10 24.9 54.9 36-65K0D165S 171 6 3/4 3 18X9 18X9 26.7 58.8 36-65P9LI71S 172 6 3/4 2 19X10 16X10 25.8 56.8 36-65K0I172S 178 7 3 16X9 16X10 27.5 60.6 36-65P0D178S 178 7 3 19X9 16X12 26.7 58.8 36-65P2I178S 203 8 2 18X9 16X10 28.8 63.5 36-65KHE203S 216 8 1/2 2 19X10 19X16 32.4 71.4 36-65KHJ216S Diameter Flush Hole Buttons Dia x Qty Weight Product No FLAT FACE MM Inch Outer Front KG LBS 152 6 2 16X8 16X4 24.4 53.7 36-6578D152S 154 6 2 16X8 16X4 24.6 54.2 36-6578D154S 156 6 1/8 2 19X8 16X10 24.1 53.1 36-6570I156S 156 6 1/8 2 16X8 16X6 24.8 54.6 36-6578D156S 165 6 1/2 2 16X8 16X10 25.1 55.4 36-6570D165S 172 6 3/4 2 19X10 16X11 25.8 56.9 36-65I1I172S 172 6 3/4 2 19X8 16X11 25.8 56.9 36-6571I172S 178 7 2 16.7X10 16X6 26.5 58.4 36-65I2D178S 190 7 1/2 3 18X10 18X8 29.3 64.6 36-65NIJ190SN 203 8 3 18X10 18X8 30.6 67.4 36-65NHE203N 216 8 1/2 3 18X9 16X16 32.0 70.5 36-65NHE216S 220 8 2/3 2 16X10 16X16 32.2 71.0 36-65IHD220P 254 10 2 19X2 16X10 39.9 87.9 36-65LII254S Diameter Flush Hole Buttons Dia x Qty Weight Product No CONCAVE MM Inch Outer Front KG LBS 165 6 1/4 3 18X9 16X4 25.8 56.9 36-65O0E165S 171 6 3/4 3 18X9 18X6 25.9 57.0 36-65O2L171S 178 7 3 16X9 16X6 26.0 57.3 36-65O2D178K Diameter Flush Hole Buttons Dia x Qty Weight Product No CONVEX QL SHANKS QL80 MM Inch Outer Front KG LBS 203 8 2 19X10 16X13 50.5 111.3 36-85KEI203S 216 8 1/2 2 19X10 16X16 51.8 114.2 36-85KHI216S 240 9 4/9 2 19X10 16X20 55.3 121.9 36-85KII240S 254 10 2 19x12 16x24 59.4 130.9 36-85MII254S Diameter Flush Hole Buttons Dia x Qty Weight Product No FLAT FACE MM Inch Outer Front KG LBS 203 8 3 19X9 16X15 50.6 111.5 36-85NGI203S 216 8 1/2 2 19X10 16X16 50.8 111.9 36-85IHI216S 225 8 7/8 2 19x10 16x14 53.2 117.3 36-85IFI225S 227 8 7/16 3 16X18 16X17 53.5 117.9 36-85UID227S 228 9 3 16X18 16X17 53.6 118.1 36-85UID228S 254 10 2 19X12 16X24 59.8 131.7 36-85LII254S 270 10 5/8 3 19x12 16x25 65.2 143.7 36-85QII270S 305 12 3 19X18 16X29 79.2 174.5 36-85UJI305S Diameter Flush Hole Buttons Dia x Qty Weight Product No CONCAVE

33. 33 DTH PRODUCT CATALOGUE DTH SHANKS MAINTENANCE BUTTON BIT GRINDING When the button bit was first introduced, it was widely assumed that sharpening was unnecessary. Such an understanding was not unfortunate since the button bit is also subjected to wear and tear even if it may give, when compared to the conventional bits; a 300% increase in footage before sharpening becomes necessary. If re-sharpening is imperfect or if not done at the correct intervals, the button bit is likely to lose penetration speed and thereafter be subject to failure. While it was granted that in softer formations, an unsharpened button bit may continue to serve without carbide failure long after it ought to have been withdrawn from service it must also be appreciated that a similarly abused bit in a massive crystalline formation will very quickly fail. It is essential to remember that in hard rock, button bits are susceptible to failure from over drilling in the same way as any other bit. It is more economical to regrind too soon than to run the risk of damage by regrinding too late. GUAGE BUTTONS When the bit is withdrawn from the bore, it will be noticed that the gauge buttons are worn in such a way that the outermost wear faces are equidistant from the bit center. When regrinding the gauge buttons it is essential to maintain the equidistance. This is best achieved by grinding in such a way as to leave a very tiny unground portion on the extreme outer edge of each button. A perfect circle of the buttons can thus be maintained BUTTON GRINDING The object of grinding is to return the carbides to their original shape. This, in effect, means the removing of an equal depth of carbide from unworn areas of each insert. For the gauge buttons this means that most of the material must be ground from the in - ner side of the button hemisphere gradually extending around until only the slight unground outer portion is left as mentioned earlier. For the inner buttons the grinding must be done around the base of the hemisphere where it emerges from the steel bit body, since the wear generally occurs at the crown. AFTER REGRINDING RES TO RED SHAPE WEAR AFTER DRILLING REGROUND HEIGHT ORIGINAL HEIGHT OF STEE L ORIGINAL SHAPE OF CARBIDE STEEL GRINDING It will be noticed that after the button grinding is complete, there may remain an excess of steel between the buttons. This must be removed. More significantly, the chip-ways around the periphery of the bit must be restored to approximately to the original depth to facilitate free scavenging of cuttings from the bit face.in bits with central flushing, special attention must be paid to see that the free flow of exhaust air from the hammer is not in any way impeded by metal expansion around the flushing hole. Such an obstruction can seriously affect the efficiency of the hammer, and must be removed while grinding. ORIGINAL SHAPE OF CARBIDE WEAR AFTER DRILLIN G AFTER GRINDING REST ORED SHAPE • A reliable pencil type air grinder capable of approximately 25000rpm. • Spindle mounted grind stones, 1” (or 1.5”) x 1” (or 0.75”) x0.25” spindle, and suitable for high speeds. • One unused new bit similar to the one being grounded (this may be dispensed by experience), or a button guage. • Safety glasses and protective clothing. Pencil type air grinders consume very little air, and it is best if bit regrinding is done while drilling is in progress. Ringing a button bit does not require brute strength; rather it is an art and the lighter the touch, the better. With proper care the button bit will greatly reduce drilling costs. EQUIPMENT REQUIRED If a new bit is likely to fail due to material or manufacturing defects, it will normally do so in the initial half regrind life. The nature of such defects is dealt with later, but it is wise to withdraw and check any new bit early in life. Sometimes the gauge buttons may show slightly uneven wear or removal, i.e. while most show normal wear patterns the odd button may show excessive wear. This may be attributed to the slightly variation in setting of the gauge buttons. In such a vase, one or two buttons may be over ground while majority still requires no grinding. Prolonged initial drilling may thus lead to individual inset failure. WHEN TO REGRIND

21. 21 DTH PRODUCT CATALOGUE MACH SHANKS MX40 MM Inch Outer Front KG LBS 105 4 1/8 2 14X8 12X6 9.3 20.5 36-X4967105S 110 4 1/3 2 14X8 12X6 9.4 20.8 36-X4967110S 115 4 1/2 2 14X8 13X6 9.5 21.0 36-X4968115S 121 4 3/4 2 14X8 13X7 10.3 22.7 36-X4978121S 127 5 2 16X8 13X7 10.5 23.2 36-X497B127S 130 5 1/8 2 14X8 14X8 11.5 25.4 36-X4989130S 140 5 1/2 2 16X8 16X8 11.4 25.2 36-X498D140S 152 6 2 16X8 14X9 13.3 29.3 36-X499C152S 178 7 2 16X10 16X13 18.3 40.3 36-X4KED178S Diameter Flush Hole Buttons Dia x Qty Weight Product No FLAT FACE MM Inch Outer Front KG LBS 105 4 1/8 2 14X8 12X6 9.1 20.0 36-X4767105S 105 4 1/8 2 14X8 12X6 9.1 20.0 36-X4767105P 107 4 1/5 2 14X8 13X6 8.5 18.8 36-X4768107S 107 4 1/5 2 14X8 12X6 8.5 18.8 36-X4767107P 107 4 1/5 2 14X8 12X6 8.5 18.8 36-X4767107B 115 4 1/2 2 14X8 12X6 9.5 20.8 36-X4767115S 115 4 1/2 2 14X8 12X6 9.5 20.8 36-X4767115B 115 4 1/2 2 14X8 12X6 9.5 20.8 36-X4767115C 115 4 1/2 2 14X8 13X8 9.5 20.8 36-X4788115S 120 4 5/7 2 16X8 13X9 10.3 22.6 36-X479B120S 121 4 3/4 2 14X8 13X7 10.3 22.6 36-X4778121S 127 5 2 14X8 14X6 10.4 22.8 36-X4769127S 127 5 2 14X8 14X6 10.4 22.8 36-X4769127P 127 5 2 14X8 14X7 10.4 22.8 36-X4779127B 127 5 2 14X8 14X6 10.4 22.8 36-X4769127D 130 5 1/8 2 14X8 14X7 11.0 24.2 36-X4779130S 133 5 1/4 2 14X8 14X6 11.0 24.2 36-X4769133S 133 5 1/4 2 14X8 14X6 11.0 24.2 36-X4769133P 140 5 1/2 2 16X8 14X10 12.5 27.6 36-X470C140S 140 5 1/2 2 16X8 14X10 12.5 27.6 36-X470C140D 146 5 3/4 2 16X8 14X10 12.6 27.8 36-X470C146S 150 6 2 16X8 14X10 11.9 26.3 36-X470C150S 165 6 1/2 2 16X8 14X10 14.1 31.1 36-X470C165S 165 6 1/2 2 16X8 16X10 14.1 31.3 36-X470D165P Diameter Flush Hole Buttons Dia x Qty Weight Product No CONCAVE MM Inch Outer Front KG LBS 105 4 1/8 2 14X8 12X6 9.1 20.1 36-X4867105S 108 4 1/4 2 14X8 13X6 9.4 20.6 36-X4868108P 115 4 1/2 2 14X8 14X7 9.5 21.0 36-X4879115S 115 4 1/2 2 14X8 13X7 9.5 21.0 36-X4878115S 121 4 3/4 2 14X8 13X8 9.8 21.7 36-X4888121P 127 5 2 14X8 14X8 10.3 22.7 36-X4889127S 127 5 2 14X8 14X8 10.3 22.7 36-X4889127P 127 5 2 14X8 14X8 10.3 22.7 36-X4889127D 130 5 1/8 3 14X9 13X11 10.5 23.1 36-X4O18130P 133 5 1/4 2 14X8 14X9 10.7 23.6 36-X4899133S 133 5 1/4 2 14X8 14X9 10.7 23.6 36-X4899133P 133 5 1/4 2 14X8 14X9 10.7 23.6 36-X4899133D 140 5 1/2 2 16X8 14X10 12.3 27.1 36-X480C140S 140 5 1/2 2 16X8 14X10 12.3 27.1 36-X480C140P 140 5 1/2 2 16X8 14X10 12.3 27.1 36-X480C140D 146 5 3/4 2 16X8 16X10 12.8 28.3 36-X480D146S 150 6 2 16X8 16X10 13.2 29.1 36-X480D150S 191 7 1/2 3 16X9 16X12 17.2 38.0 36-X4O2D191D Diameter Flush Hole Buttons Dia x Qty Weight Product No CONVEX

24. 24 DTH PRODUCT CATALOGUE DHD340 MM Inch Outer Front KG LBS 105 4 1/8 2 14X8 12X7 7.9 17.4 36-43777105S 108 4 1/4 2 14X8 12X6 8.0 17.6 36-43767108S 110 4 1/3 2 14X8 12X6 8.2 18.0 36-43767110S 115 4 1/2 2 14X8 12X6 8.4 18.4 36-43767115P 115 4 1/2 2 14X8 13X6 8.4 18.6 36-43768115S 115 4 1/2 2 14X8 12X6 8.4 18.6 36-43767115B 120 4 5/7 2 16X8 14X7 9.3 20.6 36-4377C120S 121 4 3/4 2 14X8 13X8 9.3 20.6 36-43788121P 127 5 2 16X8 14X7 9.4 20.7 36-4377C127S 127 5 2 14X8 14X7 9.4 20.7 36-43779127B 130 5 1/8 2 16X8 14X6 9.4 20.7 36-4376C130S 140 5 1/2 2 16X8 14X8 10.5 23.2 36-4378C140S 146 5 3/4 2 16X8 14X8 11.1 24.4 36-4378C146S 152 6 2 16X8 16X10 12.3 27.1 36-4370D152S 159 5 1/2 2 16X8 14X10 12.6 27.8 36-4370C159S Diameter Flush Hole Buttons Dia x Qty Weight Product No CONCAVE MM Inch Outer Front KG LBS 105 4 1/8 2 13X7 12X7 7.9 17.3 36-43575105S 115 4 1/2 2 14X8 13X7 8.4 18.6 36-43878115S 115 4 1/2 2 14X8 12X7 8.4 18.3 36-43877115B 120 4 5/7 2 14X8 12X7 9.0 19.8 36-43877120B 121 4 3/4 2 14X8 13X7 9.1 20.1 36-43878121S 127 5 2 14X8 14X6 9.2 20.3 36-43869127S 127 5 2 14X8 12X10 9.2 20.3 36-43807127C 130 5 1/8 3 14X9 13X11 9.4 20.7 36-43O18130P 133 5 1/4 2 14X8 14X8 9.5 20.8 36-43889133S 135 5 1/3 2 14X8 14X8 9.6 21.1 36-43889135S 140 5 1/2 2 16X8 16X7 10.2 22.5 36-4387D140S 140 5 1/2 2 16X8 14X10 10.2 22.5 36-4380C140C 152 6 2 16X8 14X10 12.1 26.7 36-4380C152S Diameter Flush Hole Buttons Dia x Qty Weight Product No CONVEX DHD350 MM Inch Outer Front KG LBS 125 4 15/16 2 14X8 14X7 14.0 30.9 36-53979125S 127 5 2 14X8 14X7 14.5 32.0 36-53979127S 130 5 1/8 2 14X8 14X8 14.9 32.8 36-53989130S 140 5 1/2 2 16X8 16X8 16.6 36.5 36-5398D140S 140 5 1/2 2 16X8 14X10 16.6 36.5 36-5390C140S 146 5 3/4 2 16X8 14X10 17.1 37.6 36-5390C146S 150 6 2 18X8 16X10 17.5 38.5 36-5390E150S 152 6 2 16X8 16X10 17.9 39.4 36-5390D152S 165 6 1/2 2 16X8 16X10 18.9 41.6 36-5390D165S 203 8 2 18X10 16X16 22.1 48.6 36-53KHE203S Diameter Flush Hole Buttons Dia x Qty Weight Product No FLAT FACE MM Inch Outer Front KG LBS 125 4 15/16 2 14X8 14X7 14.2 31.3 36-53779125S 127 5 2 14X8 14X7 14.5 31.9 36-53779127S 140 5 1/2 2 16X8 14X10 16.4 36.2 36-5370C140S 146 5 3/4 2 16X8 14X10 16.7 36.7 36-5370C146S 150 6 2 16X8 16X10 16.9 37.1 36-5370D150S 152 6 2 16X8 16X10 17.0 37.5 36-5370D152S 165 6 1/2 2 16X8 16X10 18.6 41.1 36-5370D165S 190 7 1/2 2 16X10 16X14 22.8 50.2 36-53IFD190S 200 8 2 16X10 16X14 23.6 51.9 36-53IFD200S Diameter Flush Hole Buttons Dia x Qty Weight Product No CONCAVE DHD SHANKS

32. 32 DTH PRODUCT CATALOGUE OTHER SHANKS NUMA Diameter Flush Hole Buttons Dia x Qty Weight Product No CONCAVE MM Inch Outer Front KG LBS 254 10 2 19X12 16X24 93.1 205.1 36-N1LII254S 270 10 5/8 3 19X12 16X25 97.5 215.0 36-N1QII270S 280 11 3 19X12 16X27 100.0 220.2 36-N1QJI280S 292 11 1/2 3 19X21 16X23 102.0 224.8 36-N1UII292S 305 12 3 19X18 19X15 103.5 228.2 36-N1UJI305S 16X13 330 13 3 19X18 19X18 110.4 243.4 36-N1UJI330S 16X13 Diameter Flush Hole Buttons Dia x Qty Weight Product No FLATFACE MM Inch Outer Front KG LBS 115 4 4/8 2 16X8 13X6 9.1 20.0 36-Q496B115S-04 115 4 4/8 2 16X8 13X6 9.1 20.0 36-Q496B115S-04 127 5 2 16X8 13X6 10.5 23.5 36-Q497B127S QLX40 Diameter Flush Hole Buttons Dia x Qty Weight Product No FLATFACE MM Inch Outer Front KG LBS 127 5 2 16 X 8 14 X 8 10.1 22.3 36-T498C127S Diameter Flush Hole Buttons Dia x Qty Weight Product No CONCAVE MM Inch Outer Front KG LBS 127 5 2 16X8 13X6 10.5 23.5 36-Q476C127S Diameter Flush Hole Buttons Dia x Qty Weight Product No CONCAVE MM Inch Outer Front KG LBS 115 4 4/8 2 14 X 8 13 X8 9.8 21.6 36-T4788115S 115 4 4/8 2 16 X8 13 X 6 9.9 21.8 36-T476B115S 127 5 2 16 X 8 14 X 6 10.5 23.5 36-T479C127S 127 5 2 16 X 8 14 X 8 10.1 22.3 36-T498C127S TD40 Diameter Flush Hole Buttons Dia x Qty Weight Product No CONCAVE MM Inch Outer Front KG LBS 115 4 4/8 2 14x6 14x4 7.2 15.87 36-RC4169115S 127 4 1/2 2 14x6 14x4 8 17.63 36-RC4169127S RC 4 Diameter Flush Hole Buttons Dia x Qty Weight Product No FLAT FACE MM Inch Outer Front KG LBS 140 5 1/2 2 16x6 14x10 15.6 34.93 36-RC530C140S 140 5 1/2 2 16x6 16x8 15.6 34.93 36-RC538D140S RC 5 Diameter Flush Hole Buttons Dia x Qty Weight Product No CONCAVE MM Inch Outer Front KG LBS 140 5 1/2 2 16x6 16x6 15.6 34.93 36-RC519D143S 143 5 1/2 2 16x6 16x4 15.5 34.17 36-RC527D140S

49. 49 DTH PRODUCT CATALOGUE JDM10SD HAMMER SL.NO NAME OF THE ITEM QTY PART NO 1 TOP SUB (6 5/8 API REG PIN) 1 NO 15-1JX100-65ARM 2 CHECK VALVE 1 NO 19-37138R 3 SPRING 1 NO 17-331220 4 BUFFER RING 1 NO 27-181310 5 AIR DISTRIBUTOR 1 NO 12-1JX100 6 “O” RING FOR AIR DISTRIBUTOR 1 NO 37-13504H 7 INNER CYLINDER 1 NO 42-1JX100 8 PISTON 1 NO 52-1CX100 9 WEAR SLEEVE 1 NO 45-1CX100 10 PISTON RETAINER RING 2 NO 89-191745 11 GUIDE BUSH 1 NO 65-1CX101 12 BIT RETAINER RING 1 NO 99-171325 13 “O” RING FOR BIT RETAINER RING 1 NO 37-16004H 14 DRIVE SUB SPACER 1 NO 29-221910 15 DRIVE SUB 1 NO 75-1JX100 SERVICE KI T (S.NO: 3,4,6,&14) 1 SET 1JX100SDK HAMMER ASSEMBLY 1 NO 34-1CX100SD-65ARMS A DEDICATED TOOL FOR 10” DRILLING SL.NO DESCRIPTION UNIT DIMENSION 1 HAMMER LENGTH W/O BIT mm 1490.0 2 HAMMER OUTSIDE DIA mm 225.0 3 HAMMER WEIGHT kg 355.0(approx) 4 CYLINDER BORE mm 179.0 5 PISTON STROKE mm 80.0 (approx.) 6 PISTON WEIGHT kg 68.0 7 HOLE SIZES mm 254 - 305 8 WRENCH SIZE A/F mm A/F 152 / W- 60.0 9 SUITABLE SHANK ----- SD10 (With Foot Vlave) HAMMER SPECIFICATION JDM SERIES 1 2 3 4 5 6 7 15 9 8 10 11 12 13 14 SD10 10 * TWO START THREAD ON TOP SUB & DRIVE SUB JDM10SD Air Consumption CFM 690 980 1610 1290 2200 1910 PSI 150 200 300 250 400 350 BPM 1078 1224 1468 1352 1674 1575

28. 28 DTH PRODUCT CATALOGUE QL40 MM Inch Outer Front KG LBS 105 4 1/8 2 14X8 12X6 8.5 18.7 36-45967105S 110 4 1/3 2 14X8 12X6 9.1 20.0 36-45967110S 115 4 1/2 2 14X8 12X6 9.6 21.3 36-45967115S 115 4 1/2 2 16X7 12X7 10.1 22.2 36-4567A115S 121 4 3/4 2 14X8 12X7 10.9 23.9 36-45977121S 127 5 2 16X8 13X7 11.5 25.4 36-4597B127S 127 5 2 19X7 13X7 11.9 26.1 36-4567G127S 130 5 1/8 2 14X8 14X8 12.0 26.5 36-45989130S 140 5 1/2 2 14X8 14X8 12.9 28.3 36-45989140S 152 6 2 16X8 14X9 14.2 31.3 36-4599C152S Diameter Flush Hole Buttons Dia x Qty Weight Product No FLAT FACE MM Inch Outer Front KG LBS 105 4 1/8 2 14X8 12X6 8.0 17.6 36-45767105S 110 4 1/3 2 14X8 12X6 8.7 19.1 36-45767110S 115 4 1/2 2 14X8 12X6 9.5 20.8 36-45767115S 121 4 3/4 2 14X8 12X6 10.5 23.1 36-45767121S 127 5 2 14X8 14X7 11.3 24.9 36-45779127S 130 5 1/8 2 14X8 14X7 11.9 26.3 36-45779130S 140 5 1/2 2 14X8 14X8 12.6 27.8 36-45789140S Diameter Flush Hole Buttons Dia x Qty Weight Product No CONCAVE MM Inch Outer Front KG LBS 105 4 1/8 2 14X8 12X6 8.2 18.1 36-45867105S 110 4 1/3 2 14X7 12X6 8.5 18.7 36-45567110S 115 4 1/2 2 14X8 14X7 9.3 20.5 36-45879115S 121 4 3/4 2 14X8 14X6 10.2 22.5 36-45869121S 127 5 2 14X8 14X8 11.1 24.4 36-45889127S 130 5 1/8 2 14X8 14X8 11.7 25.7 36-45889130S 140 5 1/2 2 14X8 14X8 12.5 27.6 36-45889140S Diameter Flush Hole Buttons Dia x Qty Weight Product No CONVEX QL50 MM Inch Outer Front KG LBS 125 5 2 14X8 14X7 14.6 32.1 36-55979125S 127 5 2 14X8 14X7 14.9 32.7 36-55979127S 130 5 1/8 3 14X9 14X9 15.0 33.1 36-55P99130B 140 5 1/2 2 16X8 16X8 15.6 34.4 36-5598D140S 146 5 3/4 2 16X8 16X8 16.0 35.2 36-5598D146S 152 6 2 16X8 16X10 16.3 35.8 36-5590D152S 165 6 1/2 2 16X8 16X10 18.5 40.8 36-5590D165S Diameter Flush Hole Buttons Dia x Qty Weight Product No FLAT FACE MM Inch Outer Front KG LBS 125 5 2 14X8 14X7 14.5 31.9 36-55779125S 127 5 2 14X8 14X7 14.8 32.5 36-55779127S 130 5 1/8 3 16X9 14X9 15.1 33.2 36-55N9C130C 140 5 1/2 2 16X8 14X8 15.8 34.7 36-5578C140S 146 5 3/4 2 16X8 16X8 16.0 35.3 36-5578D146S 152 6 2 16X8 16X10 16.7 36.8 36-5570D152S 165 6 1/2 2 16X8 16X10 18.0 39.6 36-5570D165S 165 6 1/2 2 16X10 16X13 18.3 40.3 36-55IED165S Diameter Flush Hole Buttons Dia x Qty Weight Product No CONCAVE QL SHANKS MM Inch Outer Front KG LBS 127 5 2 14X8 14X7 14.7 32.3 36-55879127S 130 5 1/8 3 14X9 14X10 15.0 33.1 36-55O09130P 134 5 2/7 3 14X9 14X10 15.2 33.5 36-55O09134P 140 5 1/2 2 16X8 16X8 15.5 34.5 36-5588D140S 140 5 1/2 3 16X9 14X10 15.5 34.5 36-55O0C140D 146 5 3/4 2 16X8 16X8 15.9 35.1 36-5588D146S Diameter Flush Hole Buttons Dia x Qty Weight Product No CONVEX

68. 68 DTH PRODUCT CATALOGUE DRT9RK HAMMER SL.NO NAME OF THE ITEM QTY PART NO 1 TOP SUB 1 NO 15-1TX100-D17M 2 CHECK VALVE CAP 1 NO 57-704539 3 CHECK VALVE 1 NO 19-56085M 4 SPRING 1 NO 17-431412 5 TOP VALVE 1 NO 12-1TX100 6 CONTROL TUBE 1 NO 35-9T9000 7 CHOKE 1NO 47-2225NA 8 BUFFER RING 1 NO 27-121009 9 METAL SPACER 1 NO 29-121013 10 LOCK PLATE (2 PIECES) 1 SET 49-110712 11 PISTON 1 NO 52-9T9000 12 WEAR SLEEVE 1 NO 45-9T9000 13 PISTON RETAINER RING 1NO 89-160750 14 GUIDE BUSH 1 NO 65-9T9000 15 “O” RING FORGUIDE BUSH 3 NO 37-13204H 16 BIT RETAINER RING 1 NO 99-151219 17 “O” RING FOR BRR 1 NO 37-13204H 18 DRIVE SUB SPACER 1 NO 77-19165E 19 DRIVE SUB 1 NO 75-9T9000 SERVICE KI T (S.NO: 2,4,7,15&17) 1 SET 1TX100R1K HAMMER ASSEMBLY 1 NO 34-9T9000R1-D17MR A DEDICATED TOOL FOR 9” DRILLING SL.NO DESCRIPTION UNIT DIMENSION 1 HAMMER LENGTH W/O BIT mm 1172.0 2 HAMMER OUTSIDE DIA mm 195.0 3 HAMMER WEIGHT kg 195.0 4 CYLINDER BORE mm 157.3 5 PISTON STROKE mm 80.0 (approx.) 6 PISTON WEIGHT kg 51.20 7 HOLE SIZES mm 228.6 - 254 8 WRENCH SIZE A/F mm A/F140 / W- 48.0 9 SUITABLE SHANK ----- RK1 (Without Foot Valve) HAMMER SPECIFICATION DRT SERIES * THREE START THREAD ON TOP SUB & DRIVE SUB DRT9RK Air Consumption CFM 511 787 1446 1100 2227 1823 PSI 150 200 300 250 400 350 BPM 1049 1176 1441 1315 1664 1556 1 2 10 5 9 8 13 14 16 RK1 12 11 6 7 3 18 17 15 19 4

92. 92 DTH PRODUCT CATALOGUE 34 - - / / 26 2B2500 33 BR 090 R 123 1 A R L W DTH HAMMER CODE ODEX CODE HAMMER CODE / SN SHANK TYPE TOP SUB PIN 2.5 D Female R-ROPE THREAD T-T THREAD WITH CARBIDE ON TOP SUB W-WELDED T-THREADED BIT SHANK PILOT DIAMETER S - STANDARD R - REVERSIBLE L - LARGE OD D - DEEP HOLE REAMING DIAMETER CASING PIPE OD/ID 1 THREAD RELIEF OD/ID CODE 115/102 A 142/128 B 171/157 C 196/183 D 222/205 E 273/260 F SPECIFICATION CHART HAMMER ASSEMBLY S 25DF / HARD FACING ODEX SHOCK ABSORBER 84 SA 254 65 ARMF ASSEMBLY CODE SHOCK ABSORBER DIA METER THREAD

20. 20 DTH PRODUCT CATALOGUE MACH303 MM Inch Outer Front KG LBS 90 3 1/2 2 12X6 12X6 4.7 10.4 36-34363090S Diameter Flush Hole Buttons Dia x Qty Weight Product No FLAT FACE MACH44 MM Inch Outer Front KG LBS 140 5 1/2 2 16X8 14X8 11.3 24.9 36-4498C140S Diameter Flush Hole Buttons Dia x Qty Weight Product No FLAT FACE MM Inch Outer Front KG LBS 108 4 1/4 2 14X8 12X6 9.2 20.3 36-44767108S 127 5 2 14X8 14X7 10.4 22.9 36-44779127S 133 5 1/4 2 14X8 14X7 11.0 24.3 36-44779133S 140 5 1/2 2 14X8 14X8 12.3 27.1 36-44789140S 150 6 2 16X8 14X10 11.7 25.9 36-4470C150S Diameter Flush Hole Buttons Dia x Qty Weight Product No CONCAVE MM Inch Outer Front KG LBS 120 4 5/7 2 14X8 13X7 9.7 21.5 36-44878120S 140 5 2 14X8 14X8 11.4 25.0 36-44889140S 150 6 2 16X8 16X10 13.2 29.1 36-4480D150S Diameter Flush Hole Buttons Dia x Qty Weight Product No CONVEX MACH50 MM Inch Outer Front KG LBS 165 6 1/2 2 16X8 16X10 19.1 42.0 36-5490D165S Diameter Flush Hole Buttons Dia x Qty Weight Product No FLAT FACE MM Inch Outer Front KG LBS 140 5 1/2 3 16X9 14X9 16.8 37.0 36-54N9C140S 146 5 3/4 2 16X8 14X10 17.0 37.4 36-5470C146S 150 6 2 16X8 16X8 17.3 38.1 36-5478D150S Diameter Flush Hole Buttons Dia x Qty Weight Product No CONCAVE MACH SHANKS MM Inch Outer Front KG LBS 135 5 1/3 2 16X8 16X4 16.2 35.7 36-5487C135S 14X3 140 5 1/2 2 16X8 16X7 16.5 36.4 36-5487D140S 146 5 3/4 3 16X9 16X10 17.3 38.1 36-54O0D146S 150 6 2 16X8 16X10 17.7 38.9 36-5480D150S Diameter Flush Hole Buttons Dia x Qty Weight Product No CONVEX

34. 34 DTH PRODUCT CATALOGUE Only the slightest anti-taper is required at the periphery of a well-designed button bit. It is essential to n remember that the gauge buttons are inserted at an angle to the face buttons. As a consequence, if the anti - taper is excessive, the gauge button may fallout during work. It is rarely necessary to grind much from the periphery as the natural wear of the steel in work automatically reduces the bit body diameter. During the above mentioned operation, it is wise (until experience makes it necessary) to check the reground bit carefully against a new unused bit of same type, or by using a suitable gauge. This helps in seeing that the contours and gradients confirm as nearly as possible to the original. • See that the face buttons are so ground that they are equal in height and in same horizontal plane. • See that the gauge buttons, with respect to their outer periphery, are in the same radius. Each button should show at its outer edge a very slightly unground portion. • Check the buttons individually to see that they are roughly hemispherical in shape and not lob sided. • See that all chip ways are clear and adequate both on cutting face and ground the bit circumference. • Allow 3 degrees of anti-taper not more • See that the hammer exhaust passage within the bit is clear. • See that the reground bit counters confirm to the new unused bit. In general, a button-insert type of bit, compared to a cross or carset bit, will give two to four times the life between regrinds. It should be ground when the width of the flat developing on the outside edge of the gauge buttons is 0.25-0.33 times the diameter of the button insert itself. In soft ground this can be extended slightly but very hard rock the lesser figure should be taken as a guide. Although a well-grounded button bit will drill slightly faster than a similar cross bit, the main advantage of the button lies in its longer life between regrinds. LOSS OF BUTTONS • MANUFACTURING DEFECT This normally occurs only very early in life, usually before the first regrind. • BAD BIT GRINDING In this case the side supportive steel may have been removed when grinding. The hole becomes elongated and the button is lost. • UNDERFEEDING WHILE DRILLING IS IN PROGRESS In such a case, there is tendency for the hammer blows to drive the carbide inserts out of the body. It is, therefore important that adequate feed pressures be given at all times. • WEAR AND TEAR Frequently the first sign that bit has completed its life the “pop-out” of one or more gauge buttons, which means that they have common loose in the steel bit body. The correct use of rotation speed and feed pres sures will, however, go along way towards increasing bit life. BREAKAGE BUTTONS • FAULTY CARBIDE In button bits this is very rare. • BAD HANDLING Due to bad handling in transit carbides may chip.it is well protect carbides at all times when they are not in actual use. A wooden box with compartments for bit storage is recommended. ANTI TAPER FINISHING CHECK LIST GENERAL COMMENTS

31. 31 DTH PRODUCT CATALOGUE RK SHANKS RK1 MM Inch Outer Front KG LBS 229 9 3 18.7X12 16X24 58.5 128.9 36-R1SIE229S 241 9 1/2 3 18.7X12 16X26 60.6 133.6 36-R1SJE241S 251 9 3/4 3 18.7X12 16X24 62.3 137.3 36-R1SJE251S 254 10 3 18.7X12 16X24 62.6 138.0 36-R1SIE254S 280 11 3 18.7X12 16X30 79.0 174.2 36-R1SJE280S 292 11 1/2 3 18.7X21 16X27 79.6 175.4 36-R1SJE292S 305 12 3 18.7X12 16X33 80.2 176.8 36-R1SJE305S 331 13 3 18.7X12 16X32 92.3 203.4 36-R1SJE331S 356 14 3 19X14 16X36 98.3 216.7 36-R1TJI356S 406 16 3 19X15 16X38 106.5 234.7 36-R1XJI406S Diameter Flush Hole Buttons Dia x Qty Weight Product No FLAT FACE RK3 MM Inch Outer Front KG LBS 305 12 3 18X12 18X29 110.9 244.4 36-R3SJE305S 311 12 1/4 3 18.7X12 16X30 112.4 247.4 36-R3SJE311S 407 16 3 18.7X16 18X65 127 279.9 36-R3XKL407S Diameter Flush Hole Buttons Dia x Qty Weight Product No FLAT FACE MM Inch Outer Front KG LBS 234 9 1/4 3 19X12 18X9 55.1 121.4 36-R1QIM234S/G 241 9 1/2 3 19X12 18X9 56.5 124.5 36-R1QIM241S/G 245 9 1/2 3 19X12 18X9 56.8 125.2 36-R1QIM245S/G 251 9 3/4 3 19X12 18X9 61.3 135.1 36-R1QIM251S/G 254 10 3 19X12 18X9 61.5 135.5 36-R1QIM254S/G Diameter Flush Hole Buttons Dia x Qty Weight Product No CONCAVE MM Inch Outer Front KG LBS 311 12 1/4 3 20x18 19x9 111.2 245.1 36-R3UIA3311S/G 330 13 3 19x12 18x15 117.7 259.4 36-R3QJM330S/G 336 13 1/4 3 19x12 18x15 119.8 264.1 36-R3QJM336S/G 343 13 1/2 3 19x15 18x21 122 268.9 36-R3UJM343S/G 406 16 3 20x27 18x21 125 275.5 36-R3VJS406S/G 432 17 3 20x27 20x21 170 374.7 36-R3VKA3432S/G 445 17 1/2 3 20x27 20x21 172 379.1 36-R3UKA3445S/G 457 18 3 20x27 20x21 175.4 386.6 36-R3VKA3457/G 489 19 1/4 3 20x27 20x21 209.7 462.3 36-R3VKA3489S/G Diameter Flush Hole Buttons Dia x Qty Weight Product No CONCAVE MM Inch Outer Front KG LBS 302 12 3 19x12 18x15 103.6 228.3 36-F1QJM302S/G 311 12 1/4 3 20x18 19x9 106.2 234.1 36-1UIA3311S/G 330 13 3 19x12 18x15 112.8 248.6 36-F1QJM304S/G 336 13 1/4 3 19x12 18x15 114.5 252.4 36-F1QJM305S/G 343 13 1/2 3 19x15 18x21 117 257.9 36-F1QJM306S/G 381 15 4 19x28 19x20 129.5 285.4 36-F1QJM307S/G 406 16 4 19x28 19x24 136.9 301.8 36-F1QJM308S/G 432 17 4 19x32 19x20 145.7 321.2 36-F1QJM309S/G FD11 OTHER SHANKS SERIES CONCAVE PUMA MM Inch Outer Front KG LBS 200 7 7/8 3 19X12 16X15 45.2 99.7 36-P8QGI200S Diameter Flush Hole Buttons Dia x Qty Weight Product No CONCAVE

35. 35 DTH PRODUCT CATALOGUE THE LOB SIDED INSERT OVER DRILLING / IMPROPER GRINDING These are the most usual causes of button breakage or buttons coming loose in the steel bit body. Normally it is the gauge buttons that are most seriously affected. Gauge buttons that break will usually be found to have sheared within the body itself. This is indicative of “pinch” action resulting from insufficient or improper grinding. The diagram clearly indicates why this occurs. As the apex of each gauge-carbide wears, the carbides are subjected to increased side thrust. Instead of hemisphere chipping a clear hole for the bit to follow, the sides of the bit and the sides of the carbide inserts forced into undersize bore. If this is not corrected by regrinding, the stresses finally become so severe that the inserts are either sheared or forced out of the bitbody. ORIGINAL SHAPE OF BUT TO N LO BSIDED WEAR P AT TERN EXTREME LO BSIDED PAT TERN DUE T O WEAR AND POOR GRINDING F ALSE APEX AX IS TRUE APEX AX IS Bad grinding has exactly the same effect. It is essential to maintain the hemispherical shape of the new carbide. Furthermore, the apex of the hemisphere must be true to the axis of the insert. If this is not observed while grinding the “lob-side inset” fault will develop in such a way that the apex of the gauge button insert hemispheres will start to shift towards the center point of the rock bit. The results are same as over drilling and broken or lost inserts will normally be results. THE FLAT HEMISPHERE OVER DRILLING / IMPROPER GRINDING The second type of insert type due to over drilling or bad is illustrated in the diagram. Here the true axis/apex relationship is retained but instead of a hemisphere the insert is allowed to develop a pronounced sub hemispherical contour. Due to the flattened nature of the insert hemisphere, the tendency is for the inserts to crush rather than chip the rock. The height of the apex of the insert above the stee bit body should be half the diameter of the insert. Check this point after grinding with a vernier gauge or an insert template. The results of following the flat hemisphere fault to develop will be put excessive shock loads on the equipment. Apart from a reduced penetration speed, this can result in insert shatter, failure of the steel bit body or hammer component failure. Proper grinding is the only answer. FL AT TRUE HEIGHT OF INSERT IS HALF INSERT DIAME TER CARBIDE INSERTS BREAKAGE Finally, carbide inserts will break quite spectacularly if in contact with steel or other inserts in the bore. After a failure, all carbide and steel must be removed from the bore before drilling is continued. Buttons bits have a large advantage over the conventional cross insert bit in that the failure of one button does not normally result in the breakage of other buttons and the bit may continue to be used satisfactorily even after inserts have failed. If a button breaks, grind away any projecting carbide, regrind the entire bit, and carry on. The WDS button bit is a perfect model of skilled craftsmanship. The finest materials and the most meticulous care go into making. At every stage of manufacture, the button bit is checked and rechecked to ensure the final product a maximum of durability, efficiency and profitability . WDS button bits are the products of years of painstaking research and the unending quest for perfection.

41. 41 DTH PRODUCT CATALOGUE WIN35DH HAMMER SL.NO DESCRIPTION UNIT DIMENSION 1 HAMMER LENGTH W/O BIT mm 776.3 2 HAMMER OUTSIDE DIA mm 78.0 3 HAMMER WEIGHT kg 21.0 4 CYLINDER BORE mm 63.0 5 PISTON STROKE mm 80.0 6 PISTON WEIGHT kg 4.0 7 HOLE SIZES mm 90-115 8 WRENCH SIZE A/F mm A/F 57.0/W-40.0 9 SUITABLE SHANK - DHD 3.5 (With Foot Valve) HAMMER SPECIFICATION 1 2 3 4 5 6 7 8 9 10 11 2 12 14 13 15 16 2 18 DH D3. 5 9 17 SL.NO NAME OF THE ITEM QTY PART NO 1 TOP SUB (2 3/8 API REG PIN ) 1 NO 15-3W3500-23ARM TOP SUB ( 5D KOREAN THREAD PIN) 1 NO 15-3W3500-5DKM 2 “O” RING FOR (TS,BV,BRR) 3 NO 37-04603H 3 CHECK VALVE CAP 1 NO 57-281820 4 CHECK VALVE 1 NO 19-12069M 5 SPRING 1 NO 17-110610 6 BUFFER RING 1 NO 27-060408 7 TOP SUB SPACER 1 NO 29-060316 8 TOP VALVE 1 NO 22-3W3500 9 “O” RING FOR TV & FV 2 NO 37-02302H 10 FLAPPER VALVE 1 NO 69-562316 11 BOTTOM VALVE 1 NO 32-3W3500 12 INNER CYLINDER 1 NO 42-3W3500 13 WEAR SLEEVE 1 NO 45-3W3500 14 PISTON 1 NO 55-3W3500 15 PISTON RETAINER RING 1 NO 89-060330 16 BIT RETAINER RING 1 NO 99-060415 17 COPPER SHIM 1NO 77-07061C 18 DRIVE SUB 1 NO 75-3W3500 SERVICE KIT (S.NO:2,3,5,6,9&17) 1 SET 3W3500DHK HAMMER ASSEMBLY 1 NO 34-3W3500DH-23ARMS HAMMER ASSEMBLY 1 NO 34-3W3500DH-5DKMS A DEDICATED TOOL FOR 3.5” DRILLING WINNER SERIES * SINGLE START THREAD ON TOP SUB & DRIVE SUB CFM 50 85 130 185 PSI 100 150 200 250 WIN35DH Air Consumption BPM 1320 1615 1865 2085

42. 42 DTH PRODUCT CATALOGUE WIN45DH / MX HAMMER SL.NO DESCRIPTION UNIT DIMENSION 1 HAMMER LENGTH [45DH/MX] mm 919.6 / 955.0 2 HAMMER OUTSIDE DIA mm 98.0 3 HAMMER WEIGHT kg 37.0 4 CYLINDER BORE mm 80.0 5 PISTON STROKE mm 80.0 (approx.) 6 PISTON WEIGHT kg 8.85 7 HOLE SIZES mm 115-140 8 TOP SUB WRENCH SIZE mm A/F 61.5/W 40.0 9 SUITABLE SHANK [WIN45DH] - DHD340 (With Foot Valve) SUITABLE SHANK [WIN45MX] - MX40 (With Foot Valve) HAMMER SPECIFICATION SL.NO NAME OF THE ITEM QTY PART NO 1 TOP SUB (2 3/8 API REG PIN ) 1 NO 15-4W4500-23ARM TOP SUB ( 7D 5TPI KOREAN THREAD) 1 NO 15-4W4500-7DKM 2 “O” RING FOR T/S, B/V & BRR 3 NO 37-06203H 3 CHECK VALVE 1 NO 19-24109R 4 SPRING 1 NO 17-220610 5 BUFFER RING 1 NO 27-070510 6 TOP SUB SPACER 1 NO 29-070521 7 TOP VALVE 1 NO 22-4W4500 8 “O” RING FOR T/V & F/V 2 NO 37-02902H 9 FLAPPER VALVE 1 NO 69-692918 10 BOTTOM VALVE 1 NO 32-4W4500 11 INNER CYLINDER 1 NO 42-4W4500 12 WEAR SLEEVE [WIN45DH] 1 NO 45-4W4501 WEAR SLEEVE [WIN45MX] 1 NO 45-4W4500 13 PISTON [WIN45DH] 1 NO 55-4W4501 PISTON [WIN45MX] 1 NO 55-4W4500 14 PISTON RETAINER RING 1 NO 89-080446 15 BIT RETAINER RING [WIN45DH] 1 NO 99-070520 BIT RETAINER RING [WIN45MX] 1 NO 99-070529 16 COPPER SHIM 1 NO 77-09081C 17 DRIVE SUB [WIN45DH] 1 NO 75-4W4501 DRIVE SUB [WIN45MX] 1 NO 75-4W4500 SERVICE KIT (S.NO 2,4,5,8&16) 1 SET 4W4500MXK HAMMER ASSEMBLY [WIN45DH] 1 NO 34-4W4500DH-23ARMS HAMMER ASSEMBLY [WIN45MX] 1 NO 34-4W4500MX-23ARMS A DEDICATED TOOL FOR 4.5” DRILLING 1 2 3 4 5 6 7 8 9 8 10 2 11 13 14 17 16 2 15 12 WINNER SERIES MX40 DHD340 * SINGLE START THREAD ON TOP SUB & DRIVE SUB CFM 54 100 215 155 360 280 PSI 100 150 250 200 350 300 WIN45DH/MX Air Consumption BPM 1080 1320 1710 1530 2020 1870

60. 60 DTH PRODUCT CATALOGUE FDS70DI HAMMER A DEDICATED TOOL FOR 7.0” DRILLING SL.NO DESCRIPTION UNIT DIMENSION 1 HAMMER LENGTH W/O BIT mm 992.00 2 HAMMER OUTSIDE DIA mm 157.0 3 HAMMER WEIGHT kg 95.0(approx.) 4 CYLINDER BORE mm 127.0 5 PISTON STROKE mm 93.0(approx.) 6 PISTON WEIGHT kg 21.10(approx.) 7 HOLE SIZES mm 177.8-203.2 8 WRENCH SIZE A/F mm A/F 115.0 / W-40.0 9 SUITABLE SHANK ----- D7 HAMMER SPECIFICATION FD SERIES 1 2 6 3 5 8 12 13 15 16 17 D7 11 10 9 4 SL.NO NAME OF THE ITEM QTY PART NO 1 TOP SUB 1 NO 15-7F7001-27IFM 2 CHECK VALVE 1 NO 19-25140R 3 SPRING 1 NO 19-220912 4 TOP VALVE 1 NO 25-6M6500 5 BUFFER RING 1 NO 27-120806/A 6 LOCK PIN 1 NO 39-16125A 7 CONTROL TUBE HEAD 1 NO 10-7F7001 8 HEAD BUFFER RING 1NO 27-060405 9 TUBE 1 NO 11-6F6505 10 PISTON 1 NO 52-7F7001 11 WEAR SLEEVE 1 NO 45-7F7002 12 PISTON RETAINER RING 1 NO 89-120645 13 GUIDE BUSH 1 NO 65-7M7000 14 “O” RING FOR GUIDE BUSH 4 NO’S 37-10604H 15 BIT RETAINER RING 1NO 99-120619/B 16 “O” RING FOR BIT RETAINER RING 1 NO 37-08603H 17 DRIVE SUB 1 NO 75-7F7001 SERVICE KIT (S.NO:5,14&16) 1 SET 7F7000DIK HAMMER ASSEMBLY 1 NO 34-7F7002DI-27IFMR 14 * SINGLE START THREAD ON TOP SUB & DRIVE SUB FDS70DI Air Consumption CFM 440 680 1260 960 1940 1590 PSI 150 200 300 250 400 350 BPM 1192 1376 1686 1539 1947 1821 7

61. 61 DTH PRODUCT CATALOGUE FD80FD HAMMER A DEDICATED TOOL FOR 8.0” DRILLING SL.NO DESCRIPTION UNIT DIMENSION 1 HAMMER LENGTH W/O BIT mm 1211.40 2 HAMMER OUTSIDE DIA mm 182.0 3 HAMMER WEIGHT kg 184.0(approx.) 4 CYLINDER BORE mm 149.0 5 PISTON STROKE mm 80.0(approx.) 6 PISTON WEIGHT kg 33.9(approx.) 7 HOLE SIZES mm 203-254 8 WRENCH SIZE A/F mm A/F 140.0 / W-50.0 9 SUITABLE SHANK ----- FD8 HAMMER SPECIFICATION FD SERIES 1 2 4 5 7 8 13 15 16 FD8 14 11 6 10 3 18 19 17 * TWO START THREAD ON TOP SUB & DRIVE SUB FD80FD Air Consumption SL.NO NAME OF THE ITEM QTY PART NO 1 TOP SUB (4 1/2 API REG) 1 NO 15-8F8001-41ARM TOP SUB (3 7/8 (D17) THREAD) 1 NO 15-8F8001-D17M 2 O” RING FOR TOP SUB 1 NO 37-14005H 3 CHECK VALVE 1 NO 19-37138R 4 CHECK VALVE CHOKE 1 NO 47-0147N(A)(C)(D) 5 SPRING 1 NO 17-331220 6 TOP VALVE 1 NO 25-8F8002 7 BUFFER RING 1 NO 27-151111 8 LOCK PIN 1 NO 39-15145A 9 CONTROL TUBE HEAD 1 NO 10-8F8001 10 HEAD BUFFER RING 1NO 27-090606 11 TUBE 1 NO 11-8F8001 12 TUBE CHOKE 1 NO 47-3228NB 13 PISTON 1 NO 52-8F8002 14 WEAR SLEEVE 1 NO 45-8F8002 15 PISTON RETAINER RING 1 NO 89-140635 16 GUIDE BUSH 1 NO 65-8F8002 17 “O” RING FOR GUIDE BUSH/ BIT RETAINER RING 4 NO’S 37-13204H 18 BIT RETAINER RING 1NO 99-140819/B 19 DRIVE SUB SPACER 1 NO 77-181610 20 DRIVE SUB 1 NO 75-8F8002 SERVICE KIT (S.NO:2,4,5,12&17) 1 SET 8F8000FDK HAMMER ASSEMBLY 1 NO 34-8F8000FD-41ARMR HAMMER ASSEMBLY 1 NO 34-8F8000FD-D17MR CFM 285 520 1100 800 1860 1480 PSI 100 150 250 200 350 300 BPM 974 1192 1539 1377 1821 1686 9 12 19

76. 76 DTH PRODUCT CATALOGUE RC5 HAMMER A DEDICATED TOOL FOR 5.0” DRILLING SL.NO DESCRIPTION UNIT DIMENSION 1 HAMMER LENGTH W/O BIT mm 1253.0 2 HAMMER OUTSIDE DIA mm 121.0 3 HAMMER WEIGHT kg 72.0 4 CYLINDER BORE mm 101.7 5 PISTON STROKE mm 85.0 (approx) 6 PISTON WEIGHT kg 14 7 HOLE SIZES mm 127.00-143.00 mm 8 WRENCH SIZE A/F mm A/F 108 /W-38.0 9 SUITABLE SHANK ----- RC5 HAMMER SPECIFICATION RC SERIES SL.NO NAME OF THE ITEM QTY PART NO 1 RETURN TUBE TOP RETAINER RING 1NO 89-060325 2 RETURN TUBE TOP 1NO 32-5RC5000 3 BACK HEAD 1NO 13-5RC5000-4.5”REMFS 4 CHECK VALVE 1NO 19-060744M 5 SPRING 1NO 17-746815 6 TOP VALVE 1NO 25-5RC5000 7 COMPRESSION RING 1NO 27-108415 8 “O” RING FOR AIR DISTRIBUTOR ID 1NO 37-05002H 9 AIR DISTRIBUTOR 1NO 12-5RC5000 10 “O” RING FOR AIR DISTRIBUTOR OD 1NO 37-05103H/A 11 INNER CYLINDER 1NO 42-5RC5000 12 RETURN TUBE BOTTOM O RING 3NO 37-03501H 13 RETURN TUBE BOTTOM 1NO 43-5RC5000 14 PISTON 1NO 52-5RC5000 15 WEAR SLEEVE 1NO 45-5RC5000 16 PISTON RETAINER RING 1NO 89-100909 17 O RING FOR GUIDE BUSH 2NO 37-09403H 18 GUIDE BUSH 1NO 65-5RC5000 19 BIT RETAINER RING 1NO 99-100815 20 O RING FOR BIT RETAINER RING 1NO 37-08703H 21 DRIVE SUB 1NO 75-5RC5000 22 BIT SHROUD 1NO 63-1301012 SEAL KIT(8,10,12,17,20) 1SET 5R5000RCK HAMMER ASSEMBLY 1NO 44-5RC5000RC-4.5”REMFS 14 16 18 20 19 15 17 21 22 RC5 2 1 4 3 6 5 8 7 10 9 11 13 12 CFM 430 570 870 720 1045 PSI 250 300 400 350 450 RC5 Air Consumption BPM 1390 1520 1640 1750 1860 1225 1960 450

38. 38 DTH PRODUCT CATALOGUE STUNNER SERIES SL.NO NAME OF THE ITEM QTY PART NO 1 TOP SUB (2.5D 4 TPI BOX) 1 NO 15-2B2500-25DF TOP SUB (CHEETHA THREAD) 1 NO 15-2B2500-5DF TOP SUB (3.5D 4 TPI BOX) 1 NO 15-2B2500-35DF TOP SUB(RD50 BOX THREAD) 1 NO 15-2B2500-RD50F TOP SUB (CA21 BOX THREAD) 1 NO 15-2B2500-CA21F TOP SUB (2 IF 4TPI 5 0 BOX) 1 NO 15-2B2500-2IFF 2 “O” RING FOR TOP SUB 1 NO 37-04602H 3 CHECK VALVE 1 NO 19-23082N 4 SPRING 1 NO 17-110513 5 TOP VALVE 1 NO 22-2B2500 6 VALVE CENTRALISER 1 NO 59-121523 7 DISC VALVE 1 NO 69-421603 8 BOTTOM VALVE 1 NO 32-2B2500 9 PISTON 1 NO 52-2B2500 10 INNER CYLINDER 1 NO 42-2B2500 11 GUIDE BUSH 1 NO 65-2B2500 12 WEAR SLEEVE 1 NO 45-2B2500 13 SPLIT BUSH 1 NO B9-050437 14 BIT RETAINER RING 1 NO 99-040319 15 “O” RING FOR BIT RETAINER RING 1 NO 37-03702H 16 DRIVE SUB 1 NO 75-2B2500 SERVICE KIT (S.NO:2,4&15) 1 SET 2B2500BRK HAMMER ASSEMBLY 1 NO 34-2B2500BR-25DFS HAMMER ASSEMBLY 1 NO 34-2B2500BR-5DFS HAMMER ASSEMBLY 1 NO 34-2B2500BR-35DFS HAMMER ASSEMBLY 1 NO 34-2B2500BR-RD50FS HAMMER ASSEMBLY 1 NO 34-2B2500BR-CA21FS HAMMER ASSEMBLY 1 NO 34-2B2500BR-2IFFS A DEDICATED TOOL FOR 3” DRILLING ST25BR HAMMER 1 2 3 4 5 6 7 8 9 12 10 11 13 14 15 16 BR2 SL.NO DESCRIPTION UNIT DIMENSION 1 HAMMER LENGTH W/O BIT mm 810.0 2 HAMMER OUTSIDE DIA mm 62.0 3 HAMMER WEIGHT kg 13.0 4 CYLINDER BORE mm 42.7 5 PISTON STROKE mm 80.0 (approx.) 6 PISTON WEIGHT kg 1 . 75 7 HOLE SIZES mm 70-80 8 WRENCH SIZE A/F mm A/F 48.0 / W-32.0 9 SUITABLE SHANK --- BR2 (Without Foot Valve) HAMMER SPECIFICATION * TWO START THREAD ON TOP SUB & DRIVE SUB CFM 30 50 100 70 130 PSI 100 150 250 200 300 ST25BR Air Consumption BPM 1220 1490 1730 1930 2120

75. 75 DTH PRODUCT CATALOGUE RC4 HAMMER A DEDICATED TOOL FOR 4.0” DRILLING SL.NO DESCRIPTION UNIT DIMENSION 1 HAMMER LENGTH W/O BIT mm 1110 2 HAMMER OUTSIDE DIA mm 96 3 HAMMER WEIGHT kg 43 4 CYLINDER BORE mm 78.4 5 PISTON STROKE mm 80.0 (approx.) 6 PISTON WEIGHT kg 6.8 7 HOLE SIZES mm 102-115mm 8 WRENCH SIZE A/F mm A/F 85.0 /W-50.0 9 SUITABLE SHANK ----- RC4 HAMMER SPECIFICATION RC SERIES SL.NO NAME OF THE ITEM QTY PART NO 1 RETURN TUBE TOP RETAINER RING 1NO 89-040225 2 RETURN TUBE TOP 2NO 32-4RC4000 3 BACK HEAD 1NO 13-4RC4000-3.5”METFS 4 CHECK VALVE O RING 1NO 37-05302H 5 CHECK VALVE 1NO 19-65044M 6 SPRING 1NO 17-620610 7 TOP VALVE 1NO 25-4RC4000 8 COMPRESSION RING 1NO 27-080611 9 “O” RING FOR AIR DISTRIBUTOR ID 1NO 37-03401H 10 AIR DISTRIBUTOR 1NO 12-4RC4000 11 “O” RING FOR AIR DISTRIBUTOR OD 1NO 37-04201H 12 INNER CYLINDER 1NO 42-4RC4000 13 RETURN TUBE BOTTOM O RING 3NO 37-06702H 14 RETURN TUBE BOTTOM 1NO 43-4RC4000 15 PISTON 1NO 52-4RC4000 16 WEAR SLEEVE 1NO 45-4RC4000 17 PISTON RETAINER RING 1NO 89-070420 18 O RING FOR GUIDE BUSH 2NO 37-08001H 19 GUIDE BUSH 1NO 65-4RC4000 20 O RING FOR BIT RETAINER RING 1NO 37-07503H 21 BIT RETAINER RING 1NO 99-080618 22 DRIVE SUB 1NO 75-4RC4000 23 BIT SHROUD 1NO 63-1000810 SEAL KIT(4,10,12,14,19) 1SET 4CR4000RCK HAMMER ASSEMBLY 1NO 44-4RC4000RC-3.5”METFS 15 17 19 21 20 16 18 22 23 RC4 2 1 4 3 6 5 8 7 10 9 12 11 14 13 CFM 391 514 791 648 945 PSI 250 300 400 350 450 RC4 Air Consumption BPM 1922 2106 2275 2432 2579 500 1106 2719

77. 77 DTH PRODUCT CATALOGUE RC55 HAMMER A DEDICATED TOOL FOR 5.5” DRILLING SL.NO DESCRIPTION UNIT DIMENSION 1 HAMMER LENGTH W/O BIT mm 1255.0 2 HAMMER OUTSIDE DIA mm 134 3 HAMMER WEIGHT kg 77 4 CYLINDER BORE mm 111.8 5 PISTON STROKE mm 90.0 (approx.) 6 PISTON WEIGHT kg 19 7 HOLE SIZES mm 137-146mm 8 WRENCH SIZE A/F mm A/F 120.0 /W-50.0 9 SUITABLE SHANK ----- RC55 HAMMER SPECIFICATION RC SERIES SL.NO NAME OF THE ITEM QTY PART NO 1 RETURN TUBE TOP RETAINER RING 1NO 89-070425 2 RETURN TUBE TOP 1NO 32-5RC5500 3 BACK HEAD 1NO 13-5RC5500-4.5”REMFS 4 CHECK VALVE 1NO 19-82684M 5 SPRING 1NO 17-720708 6 TOP VALVE 1NO 25-4RC5500 7 COMPRESSION RING 1NO 27-110915 8 “O” RING FOR AIR DISTRIBUTOR ID 1NO 37-05002H 9 AIR DISTRIBUTOR 1NO 12-5RC5500 10 “O” RING FOR AIR DISTRIBUTOR OD 1NO 37-09702H 11 INNER CYLINDER 1NO 42-5RC5500 12 RETURN TUBE BOTTOM O RING 3NO 37-04401H 13 RETURN TUBE BOTTOM 1NO 43-5RC5000 14 PISTON 1NO 52-5RC5500 15 WEAR SLEEVE 1NO 45-5RC5500 16 PISTON RETAINER RING 1NO 89-110425 17 O RING FOR GUIDE BUSH 2NO 37-10702H 18 GUIDE BUSH 1NO 65-5RC5500 19 BIT RETAINER RING 1NO 99-110815 20 O RING FOR BIT RETAINER RING 1NO 37-10701H 21 DRIVE SUB 1NO 75-5RC5500 22 BIT SHROUD 1NO 63-1301012 SEAL KIT(8,10,12,17,20) 1SET 5R5500RCK HAMMER ASSEMBLY 1NO 44-5RC5500RC-4.5”REMFS 14 16 18 20 19 15 17 21 22 RC55 2 1 4 3 6 5 8 7 10 9 11 13 12 CFM 430 570 870 720 1045 PSI 250 300 400 350 450 RC55 Air Consumption BPM 1390 1520 1640 1750 1860 1225 1960 450

39. 39 DTH PRODUCT CATALOGUE SL.NO NAME OF THE ITEM QTY PART NO 1 TOP SUB (2 3/8 API REG PIN) 1 NO 15-3B3000-23ARM TOP SUB (2 3/8 API REG BOX) 1 NO 15-3B3000-23ARF 2 “O” RING FOR TOP SUB 1 NO 37-05403H 3 CHECK VALVE 1 NO 19-23082N 4 SPRING 1 NO 17-110511 5 TOP VALVE 1 NO 22-3B3000 6 VALVE CENTRALISER 1 NO 59-121921 7 DISC VALVE 1 NO 69-511902 8 BOTTOM VALVE 1 NO 32-3B3000 9 PISTON 1 NO 52-3B3000 10 INNER CYLINDER 1 NO 42-3B3000 11 GUIDE BUSH 1 NO 65-3B3000 12 WEAR SLEEVE 1 NO 45-3B3000 13 SPLIT BUSH 1 NO B9-060443 14 BIT RETAINER RING 1 NO 99-050319 15 “O” RING FOR BIT RETAINER RING 1 NO 37-04603H 16 DRIVE SUB 1 NO 75-3B3000 SERVICE KIT (S.NO:2,4&15) 1 SET 3B3000BRK HAMMER ASSEMBLY 1 NO 34-3B3000BR-23ARMS HAMMER ASSEMBLY 1 NO 34-3B3000BR-23ARFS A DEDICATED TOOL FOR 3.5” DRILLING ST30BR HAMMER SL.NO DESCRIPTION UNIT DIMENSION 1 HAMMER LENGTH W/O BIT mm 769.0 2 HAMMER OUTSIDE DIA mm 78.0 3 HAMMER WEIGHT kg 24.0 4 CYLINDER BORE mm 50.8 5 PISTON STROKE mm 82.0 (approx.) 6 PISTON WEIGHT kg 2.80 7 HOLE SIZES mm 85 - 95 8 WRENCH SIZE A/F mm A/F 57.0 /W-50.0 9 SUITABLE SHANK - BR3 (Without Foot Valve) HAMMER SPECIFICATION STUNNER SERIES 1 3 6 7 14 13 BR3 12 9 4 8 2 11 15 5 10 16 * THREE START THREAD ON TOP SUB & DRIVE SUB CFM 40 60 100 140 PSI 100 150 200 250 ST30BR Air Consumption BPM 1130 1380 1590 1780 DTH HAMMERS

47. 47 DTH PRODUCT CATALOGUE JDM60QL HAMMER SL.NO NAME OF THE ITEM QTY PART NO 1 TOP SUB 1 NO 15-6C6000-31ARM TOP SUB 1 NO 15-6C6000-31ARM/R 2 “O” RING (FOR TS , ALINGER) 2 NO 37-10505H 3 CHOKE (FULL/HALF/QUARTER) 1 NO 47-0127N/(A)(C)(D) 4 CHECK VALVE 1 NO 19-24101R 5 SPRING 1 NO 17-221017 6 STEEL MAKEUP RING 1 NO M9-110805 7 LOCK RING 1 NO 29-110812 8 AIR DISTRIBUTOR 1 NO 12-6C6000 9 “O” RING FOR A.D& B R RING 2 NO 37-08703H 10 “O” RING FOR SEATING RING 1 NO 37-08101H 11 SEATING RING 1 NO 79-111012 12 INNER CYLINDER 1 NO 42-6C6000 13 PISTON 1 NO 55-6C6000 14 WEAR SLEEVE 1 NO 45-6C6000 15 PISTON RET RING 1 NO 89-110524 16 ALIGNER (GUIDE BUSH) 1 NO 65-6C6000 17 BIT RETAINER RING 1 NO 99-110815/A 18 DRIVE SUB SPACER 1 NO 77-14121C 19 DRIVE SUB 1 NO 75-6C6000 DRIVE SUB 1 NO 75-6C6000/L SERVICE KIT (S.NO:2,3,5,9&10) 1 SET 6C6000QLK HAMMER ASSEMBLY 1 NO 34-6C6000QL-31ARMR HAMMER ASSEMBLY 1 NO 34-6C6000QL-31ARMR/R/L A DEDICATED TOOL FOR 6” DRILLING SL.NO DESCRIPTION UNIT DIMENSION 1 HAMMER LENGTH W/O BIT mm 1035.0 2 HAMMER OUTSIDE DIA mm 144.0 3 HAMMER WEIGHT kg 100.0 4 CYLINDER BORE mm 115.8 5 PISTON STROKE mm 80.0(approx.) 6 PISTON WEIGHT kg 20.0 7 HOLE SIZES mm 156-178 8 WRENCH SIZE A/F mm A/F 100.0 / W-50.0 9 SUITABLE SHANK ----- QL60 (With Foot Valve) HAMMER SPECIFICATION 1 2 3 4 5 6 7 8 9 10 11 12 13 15 14 2 16 17 QL 60 JDM SERIES * THREE START THREAD ON TOP SUB & DRIVE SUB JDM60QL Air Consumption CFM 360 560 1030 780 1590 1300 PSI 150 200 300 250 400 350 BPM 1290 1490 1820 1670 2110 1970 18 19

50. 50 DTH PRODUCT CATALOGUE JDM12SD HAMMER SL.NO NAME OF THE ITEM QTY PART NO 1 TOP SUB (6 5/8 API REG PIN ) 1 NO 15-2CX200-65ARM 2 “O” RING ( FOR TOP SUB) 1 NO 37-23005H 3 CHECK VALVE 1 NO 19-510149R 4 CHOKE 1 NO 47-0157N(A)(C)(D) 5 SPRING 1 NO 17-441411 6 BUFFER RING 1NO 27-221518 7 AIR DISTRIBUTOR 1 NO 12-2CX200 8 “O” RING FOR AIR DISTRIBUTOR 1NO 37-17305H 9 INNER CYLINDER 1 NO 42-2CX200 10 INNER CYLINDER (RETAINER RING) 1 NO 89-210891 11 PISTON 1 NO 55-2CX200 12 WEAR SLEEVE 1 NO 45-2CX200 13 PISTON RETAINER RING 1 NO 89-231545 14 BIT RETAINER RING 1 NO 99-221440 15 “O” FOR BIT RETAINER RING 1 NO 37-20905H 16 DRIVE SUB & TOP SUB SPACER 2 NO 77-272412E 17 DRIVE SUB 1 NO 75-2CX200 SERVICE KI T (S.NO: 2,4,8&15) 1 SET 2CX200SDK HAMMER ASSEMBLY 1 NO 34-2CX200SD-65ARMS A DEDICATED TOOL FOR 12” DRILLING SL.NO DESCRIPTION UNIT DIMENSION 1 HAMMER LENGTH W/O BIT mm 1624.0 2 HAMMER OUTSIDE DIA mm 270.0 3 HAMMER WEIGHT kg 540.0 4 CYLINDER BORE mm 226.0 5 PISTON STROKE mm 65.0 (approx.) 6 PISTON WEIGHT kg 124.2 7 HOLE SIZES mm 300-400 8 WRENCH SIZE A/F mm A/F 240/ W-60 9 SUITABLE SHANK ----- SD12 ( With Foot Valve) HAMMER SPECIFICATION JDM SERIES * TWO START THREAD ON TOP SUB & DRIVE SUB CFM 364 669 1440 1030 1893 PSI 100 150 250 200 300 JDM12SD Air Consumption BPM 820 1004 1296 1160 1420 2386 350 1534 1 16 3 4 5 6 7 15 12 8 10 11 13 14 SD12 9 2 16 17

69. 69 DTH PRODUCT CATALOGUE DRT11R3 / FD11 HAMMER SL.NO NAME OF THE ITEM QTY PART NO 1 TOP SUB 1 NO 15-1TX110-65ARM 2 CHECK VALVE CAP 1 NO 57-704539 3 CHECK VALVE 1 NO 19-56085M 4 SPRING 1 NO 17-431412 5 AIR DISTRIBUTOR 1 NO 12-2VX200 6 CONTROL TUBE 1 NO 35-1TX110 7 CHOKE 1 NO 47-2225NA 8 BUFFER RING 1 NO 27-151112 9 METAL SPACER 1 NO 29-151118 10 LOCK PLATE 2 NO 49-150918 11 WEAR SLEEVE 1 NO 45-1TX110 12 PISTON 1 NO 52-1TX110 13 PISTON RETAINER RIING 1NO 89-180850 14 GUIDE BUSH 1 NO 65-1TX111 GUIDE BUSH[DRT11FD] 1 NO 65-1TX110 15 “O” RING FOR GUIDE BUSH 3NO’S 37-17605H 16 BIT RETAINER RING 1 NO 99-191523 17 “O” RING FOR B.R RING [DRT11FD] 1NO 37-18303H 18 DRIVE SUB SPACER 1 NO 77-242012 19 DRIVE SUB 1NO 75-1TX101 DRIVE SUB[DRT11FD] 1NO 75-1TX110 SERVICE KIT (S.NO:(4,7,8,14&16) 1 SET 1TX110FDK HAMMER ASSEMBLY 1 NO 34-1TX110R3-65ARMR HAMMER ASSEMBLY 1 NO 34-1TX110FD-65ARMR A DEDICATED TOOL FOR 12” DRILLING SL.NO DESCRIPTION UNIT DIMENSION 1 HAMMER LENGTH W/O BIT mm 1220.0 1 HAMMER LENGTH W/O BIT[DRT11FD] mm 1240.0 2 HAMMER OUTSIDE DIA mm 240.0 3 HAMMER WEIGHT kg 305.0 4 CYLINDER BORE mm 190.0 5 PISTON STROKE mm 90.0(approx.) 6 PISTON WEIGHT kg 73.0 7 HOLE SIZES mm 300-400 8 WRENCH SIZE A/F mm A/F 155/ W 60.0 9 TOP SUB THRED CONNECTION ----- 6 5/8” API REG PIN 10 SUITABLE SHANK ----- RK3 / FD11 (W/O F.Valve) HAMMER SPECIFICATION DRT SERIES * TWO START THREAD ON TOP SUB & DRIVE SUB DRT11R3 / FD11 Air Consumption CFM 662 1020 1870 1420 2880 2360 PSI 150 200 300 250 400 350 BPM 962 1111 1361 1242 1571 1470 1 2 10 5 9 8 13 14 16 RK3 11 12 6 7 3 18 17 15 19 4 FD11

17. 17 DTH PRODUCT CATALOGUE BR2 MM Inch Outer Front KG LBS 76 3 2 12x6 11x4 2.5 5.5 36-22342076P 76 3 2 11X6 11X4 2.5 5.5 36-2234Z076P 76 3 2 12X6 10X4 2.5 5.5 36-22341076S 80 3 1/7 2 12X6 11X4 2.8 6.2 36-22342080S 89 3 1/2 2 12X7 11X6 2.8 6.2 36-22662089S 95 3 3/4 2 12X6 10X6 3.5 7.7 36-22361095S Diameter Flush Hole Buttons Dia x Qty Weight Product No FLAT FACE MM Inch Outer Front KG LBS 70 2 3/4 2 11X6 10X4 2.3 5.0 36-2215R070S 9X1 76 3 2 12X6 10X6 2.5 5.5 36-22161076S 85 3 1/3 2 12X6 10X6 2.6 5.8 36-22161085S 90 3 1/2 2 12X7 11X5 3.5 7.6 36-22452090S Diameter Flush Hole Buttons Dia x Qty Weight Product No CONCAVE MM Inch Outer Front KG LBS 70 2 3/4 2 10X6 10X5 2.3 5.0 36-2225P070B 76 3 2 11X6 11X5 2.5 5.5 36-2225Z076B 76 3 2 11X6 11X5 2.5 5.5 36-2225Z076P 86 3 2/5 2 11X7 11X6 2.9 6.3 36-2256Z086B 95 3 3/4 2 12X7 12X6 3.1 6.8 36-22563095S Diameter Flush Hole Buttons Dia x Qty Weight Product No CONVEX BR3 MM Inch Outer Front KG LBS 90 3 1/2 2 13X7 12X5 4.2 9.3 36-32655090S 90 3 1/2 2 12X7 12X5 4.2 9.3 36-32653090B 90 3 1/2 2 13X6 12X5 4.2 9.3 36-32355090S 95 3 3/4 2 13X7 13X5 4.6 10.2 36-32656095S 95 3 3/4 2 12X8 12X6 4.6 10.2 36-32963095S 95 3 3/4 2 13X7 13X5 4.6 10.2 36-32656095P 100 3 15/16 2 12X8 12X6 4.7 10.4 36-32963100S 102 4 2 14X8 12X6 4.9 10.7 36-32967102S 105 4 1/8 2 14X8 12X6 4.9 10.7 36-32967105S 130 5 1/8 2 16X8 14X8 8.2 18.1 36-3298C130S Diameter Flush Hole Buttons Dia x Qty Weight Product No FLAT FACE MM Inch Outer Front KG LBS 90 3 1/2 2 12X7 12X5 4.3 9.4 36-32453090B 90 3 1/2 2 12X7 12X5 4.3 9.4 36-32453090S 95 3 3/4 2 12X7 12X6 4.5 10.0 36-32463095S 95 3 3/4 2 12X7 12X6 4.5 10.0 36-32463095B 100 3 15/16 2 12X8 12X6 4.6 10.1 36-32763100S 100 3 15/16 2 12X8 12X6 4.6 10.1 36-32763100B 105 4 1/8 2 14X8 12X6 4.9 10.8 36-32767105S Diameter Flush Hole Buttons Dia x Qty Weight Product No CONCAVE MM Inch Outer Front KG LBS 90 3 1/2 2 12X7 12X4 4.2 9.3 36-32543090B 95 3 3/4 2 12X7 12X7 4.3 9.5 36-32573095B 100 3 7/8 2 14X8 12X6 4.7 10.3 36-32867100P 102 4 2 14X8 12X6 4.8 10.5 36-32867102P 105 4 1/8 2 14X8 12X6 5.1 11.1 36-32867105B Diameter Flush Hole Buttons Dia x Qty Weight Product No CONVEX BR SHANKS

23. 23 DTH PRODUCT CATALOGUE DHD3.5 MM Inch Outer Front KG LBS 90 3 1/2 2 12X7 12X5 4.7 10.4 36-33653090B 90 3 1/2 2 13X7 12X5 4.7 10.4 36-33655090S 90 3 1/2 2 13X6 13X6 4.7 10.4 36-33366090P 95 3.3/4 2 14X8 11X6 5.1 11.3 36-3396K095S 95 3 3/4 2 12X7 12X6 5.1 11.3 36-33663095B 95 3 3/4 2 13X7 13X6 5.1 11.3 36-33666095P 95 3 3/4 2 13X7 12X6 5.1 11.3 36-33665095B 100 3 15/16 2 14X8 12X6 5.4 11.9 36-33967100S 100 3 15/16 2 14X8 12X6 5.4 11.9 36-33967100P 100 3 15/16 2 14X8 12X6 5.4 11.9 36-33967100B 102 4 2 12X8 12X6 5.6 12.2 36-33963102B 102 4 2 14X8 12X6 5.6 12.2 36-33967102S 102 4 2 14X8 11X7 5.6 12.2 36-3397K102B 105 4 1/7 2 14X8 12X6 5.5 12.2 36-33967105S 115 4 1/2 2 14X8 13X6 6.1 13.4 36-33968115P 115 4 1/2 2 14X8 13X6 6.1 13.4 36-33968115S Diameter Flush Hole Buttons Dia x Qty Weight Product No FLAT FACE MM Inch Outer Front KG LBS 90 3 1/2 2 12X7 12X5 4.8 10.5 36-33453090S 90 3 1/2 2 12X7 12X5 4.8 10.5 36-33453090B 95 3 3/4 2 12X7 12X6 5.1 11.3 36-33463095B 95 3 3/4 2 14X6 13X4 5.1 11.3 36-33148095B 100 3 15/16 2 14X8 12X6 5.4 11.9 36-33767100S 102 4 2 14X8 12X6 5.5 12.2 36-33767102S 105 4 1/7 2 14X8 12X7 5.6 12.3 36-33777105S 105 4 1/7 2 14X8 12X7 5.6 12.3 36-33777105C Diameter Flush Hole Buttons Dia x Qty Weight Product No CONCAVE MM Inch Outer Front KG LBS 90 3 1/2 2 12X8 12X6 4.9 10.8 36-33863090B 90 3 1/2 2 13X7 12X6 4.9 10.8 36-33565090P 90 3 1/2 2 13X7 12X6 4.9 10.8 36-33565090S 92 3 5/8 2 11X7 11X6 4.9 10.8 36-3356Z092C 95 3 3/4 2 13X7 12X6 4.9 10.8 36-33565095C 98 3 6/7 2 12X10 12X7 5.0 10.9 36-33J73098B 100 3 15/16 2 14X8 12X6 5.3 11.7 36-33867100P 102 4 2 14X8 12X6 5.6 12.2 36-33867102B 105 4 1/7 2 14X8 13X6 5.7 12.6 36-33868105S 115 4 1/2 2 14X8 13X7 6.2 13.7 36-33878115S Diameter Flush Hole Buttons Dia x Qty Weight Product No CONVEX DHD340 MM Inch Outer Front KG LBS 105 4 1/8 2 14X8 12X6 7.9 17.4 36-43967105S 108 4 1/4 2 14X8 12X6 8.0 17.5 36-43967108S 110 4 1/3 2 14X8 12X6 8.1 17.9 36-43967110P 115 4 1/2 2 14X8 13X6 8.4 18.5 36-43968115S 115 4 1/2 2 14X8 13X7 8.4 18.6 36-43978115P 116 4 4/7 2 16X8 13X6 8.5 18.8 36-4396B116S 120 4 5/7 2 14X8 12X8 8.9 19.6 36-43987120S 127 5 2 14X8 14X8 9.3 20.5 36-43989127S 127 5 2 14X8 14X8 9.3 20.6 36-43989127P 130 5 1/8 2 16X8 14X8 9.5 21.0 36-4398C130S 135 5 1/3 2 14X8 14X8 10.1 22.2 36-43989135S 140 5 1/2 2 16X8 14X10 10.3 22.7 36-4390C140S 146 5 3/4 2 16X8 14X10 10.7 23.5 36-5390C146S 150 6 2 16X8 16X10 11.1 24.5 36-4390D150P 152 6 1/8 2 16X8 14X10 11.1 24.5 36-4390C152P 178 7 2 16X8 14X10 12.9 28.3 36-4390C178S Diameter Flush Hole Buttons Dia x Qty Weight Product No FLAT FACE DHD SHANKS

57. 57 DTH PRODUCT CATALOGUE JDC10SD HAMMER SL.NO NAME OF THE ITEM QTY PART NO 1 TOP SUB (6 5/8 API REG PIN) 1 NO 15-1JX100-65ARM 2 CHECK VALVE 1 NO 19-37138R 3 SPRING 1 NO 17-331220 4 BUFFER RING 1 NO 27-181310 5 AIR DISTRIBUTOR 1 NO 12-1JX100 6 “O” RING FOR AIR DISTRIBUTOR 1 NO 37-13504H 7 INNER CYLINDER 1 NO 42-1JX100 8 PISTON 1 NO 52-1JX100 9 WEAR SLEEVE 1 NO 45-1JX100 10 PISTON RETAINER RING 2 NO 89-191745 11 GUIDE BUSH 1 NO 65-1JX100 12 “O” RING FOR GUIDE BUSH 3 NO 37-16504H 13 BIT RETAINER RING 1 NO 99-171325 14 “O” RING FOR BIT RETAINER RING 1 NO 37-16004H 15 DRIVE SUB SPACER 1 NO 29-221910 16 DRIVE SUB 1 NO 75-1JX100 SERVICE KI T (S.NO: 3,4,6,12&14) 1 SET 1JX100SDK HAMMER ASSEMBLY 1 NO 34-1JX100SD-65ARMS HAMMER ASSEMBLY 1 NO 34-1JX100SD-65ARMS A DEDICATED TOOL FOR 10” DRILLING SL.NO DESCRIPTION UNIT DIMENSION 1 HAMMER LENGTH W/O BIT mm 1490.0 2 HAMMER OUTSIDE DIA mm 225.0 3 HAMMER WEIGHT kg 355.0(approx) 4 CYLINDER BORE mm 179.0 5 PISTON STROKE mm 80.0 (approx.) 6 PISTON WEIGHT kg 68.0 7 HOLE SIZES mm 254 - 305 8 WRENCH SIZE A/F mm A/F 152 / W- 60.0 9 SUITABLE SHANK ----- SD10 (With out Foot Valve) HAMMER SPECIFICATION JDC SERIES 1 2 3 4 5 6 7 8 10 11 13 14 15 16 SD10 9 12 10 * TWO START THREAD ON TOP SUB & DRIVE SUB CFM 555 860 1570 1190 2420 1980 PSI 150 200 300 250 400 350 JDC10SD Air Consumption BPM 940 1090 1330 1220 1540 1440

65. 65 DTH PRODUCT CATALOGUE D SERIES DM65DI HAMMER SL.NO NAME OF THE ITEM QTY PART NO 1 TOP SUB 1 NO 15-6M6500-27IFM 1 TOP SUB 1 NO 15-6M6500-31ARM 2 CHECK VALVE 1 NO 19-25140R 3 SPRING 1 NO 17-220912 4 TOP VALVE 1 NO 25-6M6500 5 CONTROL TUBE 1 NO 35-6M6500 6 CHOKE 1 NO 47-2225NA 7 LOCK PIN 1 NO 39-16118A 8 PISTON 1 NO 52-6M6500 9 WEAR SLEEVE 1 NO 45-6M6500 10 PISTON RETAINER RING 1 NO 89-110645 11 GUIDE BUSH 1 NO 65-6M6500 12 “O” RING FOR GUIDE BUSH 4 NO 37-10604H 13 BIT RETAINER RING 1 NO 99-120619 14 “O” RING FOR BIT RETAINER RING 1 NO 37-08603H 15 DRIVE SUB 1 NO 75-6M6500 16 TOP SUB ID “O” RINGS 2NO 37-07403H/A SEAL KIT (3,6,12&14) 1 SET 6M6500DIK HAMMER ASSEMBLY 1 NO 34-6M6500DI-27IFMR HAMMER ASSEMBLY 1 NO 34-6M6500DI-31ARMR A DEDICATED TOOL FOR 6.5” DRILLING SL.NO DESCRIPTION UNIT DIMENSION 1 HAMMER LENGTH W/O BIT mm 931.0 2 HAMMER OUTSIDE DIA mm 148.0 3 HAMMER WEIGHT kg 95.0 4 CYLINDER BORE mm 120.5 5 PISTON STROKE mm 90.0 (approx.) 6 PISTON WEIGHT kg 18.8 7 HOLE SIZES mm 165-203 8 WRENCH SIZE A/F mm A/F 90.0 /W-40.0 9 SUITABLE SHANK ----- D6 HAMMER SPECIFICATION * SINGLE START THREAD ON TOP SUB & DRIVE SUB 1 16 2 7 4 5 14 9 8 10 11 13 D6 6 12 15 3 CFM 399 614 1129 859 1423 PSI 150 200 300 250 350 DM65DI Air Consumption BPM 1356 1566 1751 1918 2072 400 1739 2215

71. 71 DTH PRODUCT CATALOGUE UDC37DH HAMMER A DEDICATED TOOL FOR 3.7” DRILLING SL.NO DESCRIPTION UNIT DIMENSION 1 HAMMER LENGTH W/O BIT mm 886.50 2 HAMMER OUTSIDE DIA mm 85.0 3 HAMMER WEIGHT kg 28.0 4 CYLINDER BORE mm 68.70 5 PISTON STROKE mm 80.0 (approx.) 6 PISTON WEIGHT kg 5.4 7 HOLE SIZES mm 95 - 115 8 WRENCH SIZE A/F mm A/F 63.0 /W 41.5 9 SUITABLE SHANK ----- DHD3.5 (W/O Foot Valve) HAMMER SPECIFICATION UDC SERIES 1 2 3 4 7 8 10 12 13 15 17 DHD3.5 11 9 5 SL.NO PRODUCT NAME QTY PRODUCT NO 1 TOP SUB 1 NO 15-3C3500-23ARM 2 CHECK VALVE 1 NO 19-23101R/A 3 CHOKE (FULL,HALF,QUARTER) 1 NO 47-0125N(A)(C)(D) 4 SPRING 1 NO 17-220925 5 STEEL MAKE UP RING 1 NO M9-060405/A 6 BUFFER RING 2 NO 27-060405/B 7 AIR DISTRIBUTOR 1 NO 12-3U3700 8 “O”RING FOR AIR DISTRIBUTOR 1 NO 37-03903H 9 INNER CYLINDER 1 NO 42-3U3700 10 PISTON 1 NO 52-3U3700 11 WEAR SLEEVE 1 NO 45-3U3700 12 CIRCLIP 1 NO 89-060430 13 GUIDE BUSH 1 NO 65-3U3700 14 “O” RING FOR GUIDE BUSH 1 NO 37-05403H 15 BIT RETAINER RING 1 NO 99-060416 16 “O” RING FOR BIT RETAINER RING 1 NO 37-04602H 17 DRIVE SUB 1 NO 75-3C3502 DRIVE SUB(WITH SPANNER MILLING) 1 NO 75-3C3503 SERVICE KIT (S.NO:3,4,8,14&16) 1 SET 3C3500MDK HAMMER ASSEMBLY 1 NO 34-3U3700DH-23ARMS HAMMER ASSEMBLY 1 NO 34-3U3701DH-23ARMS (WITH DRIVE SUB SPANNER MILLING) 16 6 14 * THREE START THREAD ON TOP SUB & DRIVE SUB CFM 55 100 210 150 PSI 100 150 250 200 UDC37DH Air Consumption BPM 1210 1480 1910 1710

44. 44 DTH PRODUCT CATALOGUE JDM SERIES JDM35MD / DH HAMMER SL.NO NAME OF THE ITEM QTY PART NO 1 TOP SUB 1 NO 15-3C3500-23ARM 2 CHECK VALVE 1 NO 19-23101R/A 3 CHOKE (FULL,HALF,QUARTER) 1 NO 47-0125N(A)(C)(D) 4 SPRING 1 NO 17-220925 5 LOCK RING 1 NO 29-060412 6 STEEL MAKE UP RING 1 NO M9-060405 7 AIR DISTRIBUTOR 1 NO 12-3C3500 8 “O”RING FOR AIR DISTRIBUTOR 1 NO 37-03903H 9 INNER CYLINDER 1 NO 42-3C3500 10 SEATING RING 1 NO 79-060510 11 “O”RING FOR SEATING RING 1 NO 37-05901H 12 PISTON 1 NO 55-3C3500 13 WEAR SLEEVE 1 NO 45-3C3500 14 PISTON RETAINER RING 1 NO 89-060430 15 GUIDE BUSH SPACER 1 NO 29-060511 16 BIT RETAINER RING 1 NO 99-060411/A 17 “O” RING FOR BIT RETAINER RING 1 NO 37-04602H 18 DRIVE SUB(WITH TAPER) 1 NO 75-3C3501 18 DRIVE SUB(W/O TAPER) 1 NO 75-3C3502 DRIVE SUB(JDM35MD)(W/O TAPER) 1 NO 75-3C3504 SERVICE KIT (S.NO:3,4,8,11&17) 1 SET 3C3500MDK HAMMER ASSEMBLY 1 NO 34-3C3500DH-23ARMS HAMMER ASSEMBLY(W/O TAPER) 1 NO 34-3C3501DH-23ARMS HAMMER ASSEMBLY(JDM35MD) 1 NO 34-3C3501MD-23ARMS A DEDICATED TOOL FOR 3.5” DRILLING SL.NO DESCRIPTION UNIT DIMENSION 1 HAMMER LENGTH [ 35MD/DH] mm 804.8 / 804.0 (W/O BIT) 2 HAMMER OUTSIDE DIA mm 85.0 3 HAMMER WEIGHT kg 21.6 4 CYLINDER BORE mm 68.70 5 PISTON STROKE mm 80.0 (approx.) 6 PISTON WEIGHT kg 3.9 7 HOLE SIZES mm 95 - 115 8 WRENCH SIZE A/F mm A/F 63.0 /W 41.5 9 SUITABLE SHANK [JDM35MD] ----- MD3.5 (With Foot Valve) SUITABLE SHANK [JDM35DH] ----- DHD3.5 (With Foot Valve) HAMMER SPECIFICATION 1 3 2 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 DHD3.5 MD3.5 * THREE START THREAD ON TOP SUB & DRIVE SUB CFM 80 140 220 305 PSI 100 150 200 250 JDM35MD/DH Air Consumption 250 400 BPM 1540 1880 2175 2430 3660

64. 64 DTH PRODUCT CATALOGUE D55DI HAMMER SL.NO NAME OF THE ITEM QTY PART NO 1 TOP SUB 1 NO 15-5M5501-31ARM/1 1 TOP SUB 1 NO 15-5M5501-31ARM/1/R 2 “O” RING FOR TOPSUB OD 1 NO 37-08703H 3 “O” RING FOR TOPSUB ID 2 NO 37-06303H 4 CHECK VALVE 1 NO 19-25140R 5 SPRING 1 NO 17-220912 6 TOP VALVE 1 NO 25-5M5500 7 LOCK PIN 1 NO 39-01295A 8 CONTROL TUBE 1 NO 35-5M5501 9 CHOKE 1 NO 47-2119NA 10 TURNING RINGS 1NO 27-070336 11 PISTON 1 NO 52-5M5501 12 WEAR SLEEVE 1 NO 45-5M5501 13 PISTON RET RING 1 NO 89-100527 14 GUIDE BUSH 1 NO 65-5M5500 15 “O” RING FOR GUIDE BUSH 2 NO 37-08703H 16 BIT RETAINER RING 1 NO 99-090516 17 “O” RING FOR BIT RETAINER RING 1 NO 37-08703H 18 DRIVE SUB 1 NO 75-5M5501 18 DRIVE SUB (HARD FACE) 1 NO 75-5M5501/L SERVICE KIT (S.NO:2,3,5,9,15&17) 1 SET 5M5500M50K HAMMER ASSEMBLY 1 NO 34-5M5501M50-31ARMR/1 HAMMER ASSEMBLY 1 NO 34-5M5501M50-31ARMR/1/R/L A DEDICATED TOOL FOR 5.5” DRILLING SL.NO DESCRIPTION UNIT DIMENSION 1 HAMMER LENGTH W/O BIT mm 1013.5 2 HAMMER OUTSIDE DIA mm 125 3 HAMMER WEIGHT kg 60.0(approx.) 4 CYLINDER BORE mm 96.65 5 PISTON STROKE mm 80.0 (approx.) 6 PISTON WEIGHT kg 13.1 7 HOLE SIZES mm 140-165 8 WRENCH SIZE A/F mm A/F 95.0 / W-50.0 9 SUITABLE SHANK ----- M50 HAMMER SPECIFICATION D SERIES * THREE START THREAD ON TOP SUB & DRIVE SUB 1 2 3 4 5 6 8 17 11 7 11 13 14 16 M50 9 10 15 18 CFM 219 338 621 472 782 PSI 150 200 300 250 350 D55DI Air Consumption BPM 1455 1680 1878 2057 2222

66. 66 DTH PRODUCT CATALOGUE D80M HAMMER D SERIES SL.NO NAME OF THE ITEM QTY PART NO 1 TOP SUB 1 NO 15-8M8002-41ARM/R 2 “O” RING FOR TOP SUB OD 1 NO 37-14003H 3 “O”RING FOR TOP SUB ID 2 NO 37-07403H/A 4 CHECK VALVE 1 NO 19-37148R 5 SPRING 1 NO 17-331111 6 TOP VALVE 1 NO 25-8M8000 7 LOCK PIN 1 NO 39-18149A 8 CONTROL TUBE 1 NO 35-8M8002 9 CHOKE 1 NO 47-2225NA 10 PISTON 1 NO 52-8M8000 11 WEAR SLEEVE 1 NO 45-8M8001 12 PISTON RETAINER RING 1 NO 89-150727 13 GUIDE BUSH 1 NO 65-8M8000 14 “O”RING FOR GUIDE BUSH 2 NO 37-14003H 15 BIT RETAINER RING 1 NO 99-140721 16 “O” RING FOR BIT RETAINER RING 1 NO 37-11203H 17 DRIVE SUB SPACER 1NO 29-181510/A 18 DRIVE SUB(SPM) 1 NO 75-8M8002 SEAL KIT (PRT NO 2,5,9,14&16) 1 SET 8M8000M80K HAMMER ASSEMBLY 1 NO34-8M8005M80-41ARMR/R A DEDICATED TOOL FOR 8” DRILLING SL.NO DESCRIPTION UNIT DIMENSION 1 HAMMER LENGTH W/O BIT mm 1195.0 2 HAMMER OUTSIDE DIA mm 181.0 3 HAMMER WEIGHT kg 175.0 (approx.) 4 CYLINDER BORE mm 149.40 5 PISTON STROKE mm 80.0 (approx.) 6 PISTON WEIGHT kg 41.30 7 HOLE SIZES mm 200-300 8 WRENCH SIZE A/F mm A/F 114.60 /W-63.0 9 SUITABLE SHANK ----- M80 HAMMER SPECIFICATION * SINGLE START THREAD ON TOP SUB & DRIVE SUB 1 3 2 5 4 8 15 11 9 10 12 13 M80 7 14 17 6 16 CFM 668 934 1547 1228 1891 PSI 200 250 350 300 400 D80M Air Consumption BPM 1251 1398 1532 1655 1769 18

52. 52 DTH PRODUCT CATALOGUE JDC45S HAMMER A DEDICATED TOOL FOR 4.5” DRILLING SL.NO DESCRIPTION UNIT DIMENSION 1 HAMMER LENGTH W/O BIT mm 1025.0 2 HAMMER OUTSIDE DIA mm 98.0 3 HAMMER WEIGHT kg 45.0 4 CYLINDER BORE mm 80.7 5 PISTON STROKE mm 80.0 (approx.) 6 PISTON WEIGHT kg 8.6 7 HOLE SIZES mm 115 - 127 8 WRENCH SIZE A/F mm A/F 65.0 / W-40.0 9 SUITABLE SHANK ----- S4 BIT HAMMER SPECIFICATION JDC SERIES 1 2 3 4 5 8 9 13 14 15 16 17 S4 12 11 10 6 7 SL.NO NAME OF THE ITEM QTY PART NO 1 TOP SUB (2 3/8API REG PIN) 1 NO 15-4J4501-23ARM 2 “O” RING FOR TOP SUB 1 NO 37-07503H 3 CHOKE (FULL/HALF/QUARTER) 1 NO 47-0127N(A)(C)(D) 4 CHECK VALVE 1 NO 19-23101R 5 SPRING 1 NO 17-221017 6 STEEL MAKE UP RING 1NO M9-080507/A 7 BUFFER RING 2 NO 27-080506/A 8 AIR DISTRIBUTOR 1 NO 12-4J4501 9 “O” RING FOR AIR DISTRIBUTOR 1 NO 37-05103H 10 INNER CYLINDER 1 NO 42-4J4502 11 PISTON 1 NO 52-4J4501 12 WEAR SLEEVE 1 NO 45-4J4504 13 PISTON RETAINER RING 1 NO 89-080425/A 14 GUIDE BUSH 1 NO 65-4J4501 15 “O” RING FOR GUIDE BUSH 3 NO 37-06803H 16 BIT RETAINER RING 1 NO 99-080412 17 “O” RING FOR B.R RING 1 NO 37-06803H 18 DRIVE SUB 1NO 75-4J4501 SERVICE KIT (S.NO:2,3,5,9,15&17) 1 SET 4J4501S4K HAMMER ASSEMBLY 1 NO 34-4J4503S4-23ARMS * TWO START THREAD ON TOP SUB & DRIVE SUB CFM 125 190 350 270 PSI 150 200 300 250 JDC45S Air Consumption 18 BPM 1260 1460 1790 1630

63. 63 DTH PRODUCT CATALOGUE S45S4 HAMMER SL.NO NAME OF THE ITEM QTY PART NO 1 TOP SUB 1 NO 15-4S4500-23ARM/1 1 TOP SUB 1 NO 15-4S4500-27ARM 2 “O” RING FOR TOP SUB OD 1 NO 37-06803H 3 “O” RING FOR TOP SUB ID 2 NO 37-05103H/A 4 CHECK VALVE 1 NO 19-13103R 5 SPRING 1 NO 17-110512 6 TOP VALVE 1 NO 25-4S4500 7 CONTROL TUBE 1 NO 35-4S4500 8 CHOKE 1 NO 47-1120NA 9 LOCK PIN 1 NO 39-12076A 10 PISTON 1 NO 52-4S4500 11 WEAR SLEEVE 1 NO 45-4S4500 12 PISTON RETAINER RING 1 NO 89-080430 13 GUIDE BUSH 1 NO 65-4S4500 14 “O” RING FOR GUIDE BUSH 2 NO 37-06803H 15 BIT RETAINER RING 1NO 99-070412 16 “O” RING FOR BIT RETAINER RING 1 NO 37-06203H/A 17 DRIVE SUB 1 NO 75-4S4500 SEAL KIT (PRT NO 2,5,8,14& 16) 1 SET 4S4500S4K HAMMER ASSEMBLY 1 NO 34-4S4500S4-23ARMR/1 HAMMER ASSEMBLY 1 NO 34-4S4500S4-27ARMR A DEDICATED TOOL FOR 4.5” DRILLING SL.NO DESCRIPTION UNIT DIMENSION 1 HAMMER LENGTH W/O BIT mm 912.0 2 HAMMER OUTSIDE DIA mm 98.0 3 HAMMER WEIGHT kg 42.0 4 CYLINDER BORE mm 77.6 5 PISTON STROKE mm 85.0 (approx.) 6 PISTON WEIGHT kg 7.40 7 HOLE SIZES mm 120-125 8 WRENCH SIZE A/F mm A/F 65.5 /W-50.0 9 SUITABLE SHANK ----- S4 BIT HAMMER SPECIFICATION D SERIES * THREE START THREAD ON TOP SUB & DRIVE SUB CFM 150 230 425 325 535 PSI 150 200 300 250 350 S45S4 Air Consumption 1 2 3 4 5 6 7 17 11 8 12 13 15 16 S4 9 10 BPM 1510 1740 1950 2140 2310 14

59. 59 DTH PRODUCT CATALOGUE FDS47DI HAMMER A DEDICATED TOOL FOR 4.5” DRILLING SL.NO DESCRIPTION UNIT DIMENSION 1 HAMMER LENGTH W/O BIT mm 980.0 2 HAMMER OUTSIDE DIA mm 107.0 3 HAMMER WEIGHT kg 44.5 4 CYLINDER BORE mm 88.0 5 PISTON STROKE mm 90.0 (approx.) 6 PISTON WEIGHT kg 9.40 7 HOLE SIZES mm 120-140 8 WRENCH SIZE A/F mm A/F 74.5 /W-40.0 9 SUITABLE SHANK ----- D4 * SINGLE START THREAD ON TOP SUB & THREE START THREAD ON DRIVE SUB HAMMER SPECIFICATION FD SERIES 1 2 3 4 7 8 13 17 16 D4 11 10 5 6 SL.NO PRODUCT NAME QTY PRODUCT NO 1 TOP SUB (2 3/8 API REG PIN) 1 NO 15-4F4700-23ARM 2 CHECK VALVE 1 NO 19-24109R 3 SPRING 1 NO 17-220610 4 BUFFER RING 1 NO 27-080610 5 TOP VALVE 1 NO 25-4F4700 6 CONTROL TUBE HEAD 1 NO 10-4F4700 7 TUBE 1 NO 11-4F4703 8 HEAD BUFFER RING 1NO 27-060405/A 9 C/TUBE LOCK PIN 1 NO 39-11085A 10 PISTON 1 NO 52-4F4703 11 WEAR SLEEVE 1 NO 45-4F4700 12 PISTON RETAINER RING 1 NO 89-080430 13 GUIDE BUSH 1 NO 65-4F4702 14 “O” RING GUIDE BUSH 2 NO 37-07504H 15 BIT RETAINER RING 1 NO 99-080515 16 “O” RING FOR BIT RETAINER RING 1 NO 37-06203H/A 17 DRIVE SUB 1 NO 75-4F4700 SEAL KIT (PRT NO3,4,8,14&16) 1 SET 4F4700DIK HAMMER ASSEMBLY 1 NO 34-4F4704DI-23ARMS 15 14 FDS47DI Air Consumption 12 9 CFM 230 400 730 580 880 PSI 150 200 300 250 350 BPM 1857 2144 2626 2397 2837

72. 72 DTH PRODUCT CATALOGUE UDC40 DH HAMMER A DEDICATED TOOL FOR 4.0” DRILLING SL.NO DESCRIPTION UNIT DIMENSION 1 HAMMER LENGTH W/O BIT mm 974.0 2 HAMMER OUTSIDE DIA mm 92.5 3 HAMMER WEIGHT kg 30.0 4 CYLINDER BORE mm 74.0 5 PISTON STROKE mm 80.0 (approx.) 6 PISTON WEIGHT kg 7.0 7 HOLE SIZES mm 102-127 8 WRENCH SIZE A/F mm A/F 65.0 /W 40.0 9 SUITABLE SHANK ----- DHD340 (Without Foot Valve) HAMMER SPECIFICATION UDC SERIES 1 2 3 4 5 8 9 15 16 DHD340 11 10 6 SL.NO PRODUCT NAME QTY PROUDUCT NO 1 TOP SUB (2 3/8” API REG PIN) 1 NO 15-4U4000-23ARM 2 “O”RING FOR TOPSUB 1NO 37-06203H 3 CHOKE (FULL,HALF,QUARTER) 1 NO 47-0125N(A)(C)(D) 4 CHECK VALVE 1 NO 19-23101R/A 5 SPRING 1 NO 17-221017 6 BUFFER RING 1 NO 27-070406 7 AIR DISTRIBUTOR 1 NO 12-4U4000 8 “O”RING FOR AIR DISTRIBUTOR 1 NO 37-05103H 9 INNER CYLINDER 1 NO 42-4U4000 10 PISTON 1 NO 52-4U4000 11 WEAR SLEEVE 1 NO 45-4U4000 12 PISTON RETAINER RING 1 NO 89-070711 13 GUIDE BUSH 1 NO 65-4U4000 14 BIT RETAINER RING 1 NO 99-070515/A 15 “O” RING FOR BIT RETAINER RING 1 NO 37-06203H 16 DRIVE SUB 1 NO 75-4U4000 SERVICE KIT (S.NO:2,3,5,6,8&15) 1 SET 4U4000DHK HAMMER ASSEMBLY 1 NO 34-4U4000DH-23ARMS 14 13 7 * TWO START THREAD ON TOP SUB & DRIVE SUB CFM 60 110 240 170 PSI 100 150 250 200 UDC40DH Air Consumption BPM 1135 1390 1795 1605 310 300 1970 12

45. 45 DTH PRODUCT CATALOGUE JDM45DH / QLX HAMMER SL.NO NAME OF THE ITEM QTY PART NO 1 TOP SUB 1 NO 15-4C4500-23ARM TOP SUB 1 NO 15-4C4500-27ARM 2 “O” RING FOR TOP SUB 1 NO 37-07503H 3 CHOKE’S(FULL,HALF,QUARTER) 1 NO 47-0127N(A)(C)(D) 4 CHECK VALVE 1 NO 19-23101R 5 SPRING 1 NO 17-221017 6 STEEL MAKEUP RING 1 NO M9-080507 7 LOCK RING 1 NO 29-070512 8 AIR DISTRIBUTOR 1 NO 12-4C4500 9 “O” RING FOR AIR DISTRIBUTOR 1 NO 37-05103H 10 INNER CYLINDER 1 NO 42-4C4500 11 SEATING RING 1 NO 79-070610 12 “O” RING FOR SEATING RING,BRR 2 NO 37-05901H 13 PISTON 1 NO 55-4C4500 PISTON[JDM45QLX] 1 NO 55-4C4501 14 WEAR SLEEVE 1 NO 45-4C4500 15 PISTON RET RING 1 NO 89-070425 16 ALINGER /GUIDE BUSH 1 NO 65-4C4500 GUDIE BUSH[JDM45QLX] 1 NO 65-4C4502 17 BIT RETAINER RING 1 NO 99-070509 BIT RETAINER RING[JDM45QLX] 1 NO 99-080522 18 DRIVE SUB 1 NO 75-4C4500 DRIVE SUB[JDM45QLX] 1 NO 75-4C4502 SEAL KIT (S.NO:2,3,5,9&12) 1 SET 4C4500DHK HAMMER ASSEMBLY 1 NO 34-4C4500DH-23ARMS HAMMER ASSEMBLY[JDM45QLX] 1 NO 34-4C4500QLX-23ARMS HAMMER ASSEMBLY[JDM45QLX] 1 NO 34-4C4500QLX-27ARMS A DEDICATED TOOL FOR 4.5” DRILLING SL.NO DESCRIPTION UNIT DIMENSION 1 HAMMER LENGTH W/O BIT mm 955.7 2 HAMMER OUTSIDE DIA mm 98.0 3 HAMMER WEIGHT kg 39.0 4 CYLINDER BORE mm 78.2 5 PISTON STROKE mm 80.0 (approx.) 6 PISTON WEIGHT kg 7.7 7 HOLE SIZES mm 115-127 8 WRENCH SIZE A/F mm A/F 65.0 / W - 40.0 9 SUITABLE SHANK ----- DHD340 / QLX40 (With F.V) HAMMER SPECIFICATION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 12 18 DH D34 0 JDM SERIES * THREE START THREAD ON TOP SUB & DRIVE SUB CFM 70 190 595 350 830 PSI 100 200 400 300 500 JDM45DH / QLX Air Consumption BPM 1030 1460 2440 1790 2730 QLX40

54. 54 DTH PRODUCT CATALOGUE JDC60QL / DH HAMMER A DEDICATED TOOL FOR 6.0” DRILLING SL.NO DESCRIPTION UNIT DIMENSION 1 HAMMER LENGTH W/O BIT mm 1051.0 HAMMER LENGTH W/O BIT[JDC60DH] mm 1104.9 2 HAMMER OUTSIDE DIA mm 144.0 3 HAMMER WEIGHT kg 95.0(approx.) 4 CYLINDER BORE mm 120.50 5 PISTON STROKE mm 80.0 (approx.) 6 PISTON WEIGHT kg 22.70 7 HOLE SIZES mm 152.4 - 177.8 8 WRENCH SIZE A/F mm A/F 101.0 /W-50.0 9 SUITABLE SHANK ---- QL60/DHD360 (W/O F.Valve) HAMMER SPECIFICATION JDC SERIES 1 2 3 4 5 8 9 11 15 16 17 QL60 10 12 6 7 SL.NO NAME OF THE ITEM QTY PART NO 1 TOP SUB 1 NO 15-6J6000-31ARM 2 “O” RING FOR TOP SUB 1 NO 37-11803H 3 CHECK VALVE 1 NO 19-35113R 4 CHOKE 1 NO 47-0134N (A)(C)(D) 5 SPRING 1 NO 17-231216 6 BUFFER RING 1 NO 27-120806/B 7 AIR DISTRIBUTOR 1 NO 12-6J6500 8 “O” RING FOR AIR DISTRIBUTOR 1 NO 37-09403H 9 INNER CYLINDER 1 NO 42-6J6501 10 WEAR SLEEVE 1 NO 45-6J6000 WEAR SLEEVE [JDC60DH] 1 NO 45-6J6002 11 PISTON 1 NO 52-6J6500 12 PISTON RETAINER RING 1 NO 89-110645 13 ALIGNER 1 NO 65-6J6500 ALIGNER / GUIDE BUSH[JDC60DH] 1 NO 65-6J6002 14 “O” RING FOR ALIGNER 4NO’S 37-10604H “O” RING FOR ALIGNER [JDC60DH] 2NO’S 37-10604H 15 BIT RETAINER RING 1 NO 99-120820 BIT RETAINER RING[JDC60DH] 1 NO 99-120825/A 16 “O” RING FOR BIT RETAINER RING 1 NO 37-08603H 17 DRIVE SUB 1 NO 75-6J6000 DRIVE SUB[JDC60DH] 1 NO 75-6J6003 SEAL KIT (PRT NO 2,4,5,8&14) 1 NO 6J6500QLK HAMMER ASSEMBLY[JDC60QL] 1 SET 34-6J6000QL-31ARMS HAMMER ASSEMBLY[JDC60DH] 1 SET 34-6J6000DH-31ARMS 13 14 * THREE START THREAD ON TOP SUB & DRIVE SUB CFM 320 550 920 700 PSI 150 200 300 250 350 1160 JDC60QL/DH Air Consumption BPM 1215 1400 1715 1565 1850 400 1415 1980

73. 73 DTH PRODUCT CATALOGUE UDC47DI HAMMER A DEDICATED TOOL FOR 4.7” DRILLING SL.NO DESCRIPTION UNIT DIMENSION 1 HAMMER LENGTH W/O BIT mm 999.0 2 HAMMER OUTSIDE DIA mm 108.0 3 HAMMER WEIGHT kg 45.0 4 CYLINDER BORE mm 89.0 5 PISTON STROKE mm 85.0 (approx.) 6 PISTON WEIGHT kg 10.0 7 HOLE SIZES mm 120-140 8 WRENCH SIZE A/F mm A/F 85.7 /W-40.0 9 SUITABLE SHANK ----- D4 (Without Foot Valve) HAMMER SPECIFICATION UDC SERIES 1 2 3 4 5 7 8 12 13 15 16 17 D4 11 10 9 6 SL.NO NAME OF THE ITEM QTY PART NO 1 TOP SUB 1 NO 15-4U4700-23ARM TOP SUB 1 NO 15-4U4700-31ARM TOP SUB 1 NO 15-4U4700-5DKM 2 “O” RING FOR TOPSUB 1 NO 37-07503H 3 CHOKE’S(FULL,HALF,QUARTER) 1 NO 47-012N(A)(C)(D) 4 CHECK VALVE 1 NO 19-23101R 5 SPRING 1 NO 17-221017 6 BUFFER RING 1 NO 27-080606 7 AIR DISTRIBTOR 1 NO 12-4U4700 8 “O” RING AIRDISTRIBUTOR 1 NO 37-05103H 9 INNER CYLINDER 1 NO 42-4U4700 10 PISTON 1 NO 52-4U4700 11 WEAR SLEEVE 1 NO 45-4U4700 12 PISTON RETAINER RING 1 NO 89-090430/A 13 GUIDE BUSH 1 NO 65-4U4700 14 “O” RING GUIDE BUSH 3 NO 37-07603H 15 BIT RETAINER RING 1 NO 99-080515/A 16 “O” RING FOR BIT RETAINER RING 1 NO 37-06203H/A 17 DRIVE SUB 1 NO 75-4U4700 SEAL KIT (PRT NO 2,3,5,6,8,14&16) 1 SET 4U4700DIK HAMMER ASSEMBLY 1 NO 34-4U4700DI-23ARMS HAMMER ASSEMBLY 1 NO 34-4U4700DI-31ARMS HAMMER ASSEMBLY 1 NO 34-4U4700DI-5DKMS 14 * SINGLE START THREAD ON TOP SUB & DRIVE SUB CFM 170 262 482 366 PSI 150 200 300 250 UDC47DI Air Consumption BPM 1475 1703 2086 1905 607 350 2253

93. 93 DTH PRODUCT CATALOGUE 24 P 21 B 21 114 200 CODE P - PIN B - BOX N-NO THREAD P - PIN B - BOX N-NO THREAD TOTAL LENGTH THREAD CONNECTION THREAD CONNECTION DIAMETER - THREADING CODE FLAT/PLAIN 10 2.5D 4 TPI 11 3.5D 4 TPI 12 2IF THRD 13 CA 21 BOX THRD 14 CHEETHA THRD 15 RD 50 6 TPI 16 2 3/8 API REG 17 2 3/8 API IF 18 2 7/8 API REG 19 2 7/8 API IF 20 14 076 600 23ARM W CODE DIAMETER THREAD CONNECTION ON BOTH SIDES W-WELDED F - FRICTION LENGTH EX: 600 = 6000mm 420 = 4200mm / - SPECIFICATION CHART ADAPTERS 14 WALL THICKNESS ACROSS FLAT 062 THREADING CODE 3 1/2 API REG 21 3 1/2 BECO 22 3 1/2 API IF 23 4 1/2 API REG 24 4 1/2 BECO 25 5 1/2 BECO 26 6 5/8 API REG 27 5D 5TPI KOREAN 28 7D 5TPI KOREAN 29 D17 THRD 30 PIPES

15. 15 DTH PRODUCT CATALOGUE CHEETHA MM Inch Outer Front KG LBS 83 3 1/4 2 12x6 10x4 3.2 7.1 36-37341083S 90 3 1/2 2 12x6 10x5 3.5 7.7 36-37351090S Diameter Flush Hole Buttons Dia x Qty Weight Product No FLAT FACE PANTHER MM Inch Outer Front KG LBS 110 4 1/3 2 14X8 12X6 7.1 15.7 36-47967110S 115 4 1/2 2 14X8 13X6 7.2 15.9 36-47968115S 121 4 3/4 2 14X8 13X8 8.1 17.9 36-47988121S 127 5 2 14X8 13X8 8.4 18.5 36-47988127S 140 5 1/2 2 14X8 14X8 9.8 21.6 36-47989140S 152 6 2 16X8 14X10 14.1 31.1 36-4790C152S 165 6 1/2 2 16X10 14X10 15.2 33.4 36-47K0C165S 172 6 3/4 2 16X10 16X13 16.3 35.9 36-47K3D172S Diameter Flush Hole Buttons Dia x Qty Weight Product No FLAT FACE D17 MM Inch Outer Front KG LBS 203 8 2 18X10 16X16 43.8 96.6 36-87KHE203S 216 8 1/2 2 18X10 16X18 45.2 99.6 36-87KIE216S 228 9 2 18x10 16X20 47.1 103.7 36-87KIE228S 241 9 1/2 2 18x10 16x24 49.8 109.8 36-87KIE241S 254 10 3 18X12 16X24 57.0 125.6 36-87SIE254S 267 10 1/2 3 18x12 16x24 63.0 138.9 36-87SIE267S 280 11 3 18x12 16X24 67.1 148.0 36-87SIE280S 305 12 3 18X12 16X27 69.7 153.7 36-87SJE305S 330 13 3 18X14 16X36 71.0 156.5 36-87TJE330S 337 13 1/4 3 18X14 16X36 71.8 158.3 36-87TJE337S 343 13 1/2 3 19X12 16X36 90.0 198.4 36-87SJI343S 356 14 3 19X14 16X36 105.5 232.6 36-87TJI356S Diameter Flush Hole Buttons Dia x Qty Weight Product No FLAT FACE PANTHER SHANKS FLAT FACE FLAT FACE MM Inch Outer Front KG LBS 140 5 1/2 2 16X8 14x4 9.8 21.7 36-4778Q140S 13X4 Diameter Flush Hole Buttons Dia x Qty Weight Product No FLAT FACE CONCAVE MM Inch Outer Front KG LBS 115 4 1/2 2 14x8 12x7 7.1 15.7 36-47877115B 127 5 2 14x8 14x6 7.9 17.3 36-47807127P 12X4 133 4 1/4 2 14x8 14x8 8.5 18.8 36-47889133P Diameter Flush Hole Buttons Dia x Qty Weight Product No FLAT FACE CONVEX

53. 53 DTH PRODUCT CATALOGUE JDC55QL / DH HAMMER A DEDICATED TOOL FOR 5.5” DRILLING SL.NO DESCRIPTION UNIT DIMENSION 1 HAMMER LENGTH [55QL/55DH] mm 1056.0 / 1050.0 (W/O BIT) 2 HAMMER OUTSIDE DIA mm 124.0 3 HAMMER WEIGHT kg 70.0 4 CYLINDER BORE mm 99.75 5 PISTON STROKE mm 80.0 (approx.) 6 PISTON WEIGHT kg 15.0 7 HOLE SIZES mm 140-165 8 WRENCH SIZE A/F mm A/F 90.0 / W-50.0 9 SUITABLE SHANK [JDC55QL] ----- QL50 (Without Foot Valve) SUITABLE SHANK [JDC55DH] ----- DHD350 (W/O Foot Valve) HAMMER SPECIFICATION JDC SERIES 1 2 4 3 5 8 9 11 15 17 18 19 QL50 13 12 10 6 7 SL.NO NAME OF THE ITEM QTY PART NO 1 TOP SUB 1 NO 15-5C5500-31ARM 2 CHOKE (FULL/HALF/QUARTER) 1 NO 47-0127N/(A)(C)(D) 3 CHECK VALVE 1 NO 19-24101R 4 SPRING 1 NO 17-221017 5 STEEL MAKEUP RING 1 NO M9-100705 6 LOCK RING 1 NO 29-100712 7 AIR DISTRIBUTOR 1 NO 12-5C5500 8 “O” RING FOR AIR DISTRIBUTOR 1 NO 37-06803H 9 SEATING RING 1 NO 79-100910 10 “O” RING FOR SEATING RING 1 NO 37-06002H 11 INNER CYLINDER 1 NO 42-5J5501 12 PISTON[JDC55QL] 1 NO 52-5J5501 PISTON[JDC55DH] 1 NO 52-5J5501 13 WEAR SLEEVE[JDC55QL] 1 NO 45-5J5501 WEAR SLEEVE[JDC55DH] 1 NO 45-5J5500 14 PISTON RETAINER RING[JDC55QL] 1 NO 89-090429 PISTON RET RING[JDC55DH] 1 NO 89-090324 15 GUIDE BUSH[JDC55QL] 1 NO 65-5J5501 GUIDE BUSH[JDC55DH] 1 NO 65-5J5500 16 “O” RING FOR GUIDE BUSH 1 NO 37-09003H 17 BIT RETAINER RING[JDC55QL] 1 NO 99-100716 BIT RETAINER RING[JDC55DH] 1 NO 99-090718 18 “O” RING FOR BIT RETAINER RING 1 NO 37-08402H 19 COPPER SHIM 1 NO 77-12101C 20 DRIVE SUB[JDC55QL] 1 NO 75-5C5500 DRIVE SUB[JDC55QL] 1 NO 75-5C5500/L DRIVE SUB[JDC55DH] 1 NO 75-5J5500 SERVICE KIT (S.NO:2,4,8,10,16&18) 1 SET 5J5500QLK HAMMER ASSEMBLY[JDC55QL] 1 NO 34-5J5501QL-31ARMR HAMMER ASSEMBLY[JDC55QL] 1 NO 34-5J5501QL-31ARMR/L HAMMER ASSEMBLY[JDC55DH] 1 NO 34-5J5500DH-31ARMS 14 20 16 DHD350 * TWO START THREAD ON TOP SUB & DRIVE SUB CFM 230 355 820 650 PSI 150 200 350 300 400 1005 JDC55QL/DH Air Consumption BPM 1280 1480 1960 1815 2095

55. 55 DTH PRODUCT CATALOGUE JDC65QL / DH HAMMER SL.NO NAME OF THE ITEM QTY PART NO 1 TOP SUB 1 NO 15-6J6500-31ARM 2 “O” RING FOR TOP SUB 1 NO 37-11803H 3 CHECK VALVE 1 NO 19-35113R 4 CHOKE 1 NO 47-0134N (A)(C)(D) 5 SPRING 1 NO 17-231216 6 BUFFER RING 1 NO 27-120806/B 7 AIR DISTRIBUTOR 1 NO 12-6J6500 8 “O” RING FOR AIR DISTRIBUTOR 1 NO 37-09403H 9 INNER CYLINDER 1 NO 42-6J6501 10 WEAR SLEEVE 1 NO 45-6J6500 WEAR SLEEVE [JDC65DH] 1 NO 45-6J6503 11 PISTON 1 NO 52-6J6500 12 PISTON RETAINER RING 1 NO 89-110645 13 ALIGNER/GUIDE BUSH 1 NO 65-6J6500 ALIGNER / GUIDE BUSH[JDC65DH] 1 NO 65-6J6002 14 “O” RING FOR ALIGNER 4NO’S 37-10604H “O” RING FOR ALIGNER [JDC65DH] 2NO’S 37-10604H 15 BIT RETAINER RING 1 NO 99-120820 BIT RETAINER RING 1 NO 99-120825/A 16 “O” RING FOR BIT RETAINER RING 1 NO 37-08603H 17 DRIVE SUB 1 NO 75-6J6500 DRIVE SUB 1 NO 75-6J6500/L DRIVE SUB[JDC65DH] 1 NO 75-6J6503 SEAL KIT (PRT NO 2,4,5,8&14) 1 SET 6J6500QLK HAMMER ASSEMBLY 1 NO 34-6J6500QL-31ARMS HAMMER ASSEMBLY 1 NO 34-6J6500QL-31ARMS/L HAMMER ASSEMBLY[JDC65DH] 1 NO 34-6J6500DH-31ARMS A DEDICATED TOOL FOR 6.5” DRILLING SL.NO DESCRIPTION UNIT DIMENSION 1 HAMMER LENGTH W/O BIT mm 1051.0 HAMMER LENGTH W/O BIT[JDC65DH] mm 1104.9 2 HAMMER OUTSIDE DIA mm 148.0 3 HAMMER WEIGHT kg 98.0(approx.) 4 CYLINDER BORE mm 120.50 5 PISTON STROKE mm 80.0 (approx.) 6 PISTON WEIGHT kg 22.70 7 HOLE SIZES mm 165-190 8 WRENCH SIZE A/F mm A/F 101.0 /W-50.0 9 SUITABLE SHANK QL60/DHD360 (W/O F.Valve) HAMMER SPECIFICATION JDC SERIES * THREE START THREAD ON TOP SUB & DRIVE SUB CFM 215 605 1710 1110 2390 PSI 100 200 400 300 500 JDC65QL / DH Air Consumption BPM 920 1305 1845 1595 2060 1 2 3 4 5 8 9 11 15 16 17 QL60 10 12 6 7 13 14

48. 48 DTH PRODUCT CATALOGUE JDM80QL / DH / SD HAMMER SL.NO NAME OF THE ITEM QTY PART NO 1 TOP SUB 1 NO 15-8J8000-41ARM TOP SUB 1 NO 15-8J8000-41ARM/R 2 “O” RING FOR TOP SUB 1 NO 37-14005H 3 CHECK VALVE 1 NO 19-37138R 4 CHOKE (FULL/HALF/QUARTER) 1NO 47-0147N(A)(C)(D) 5 SPRING 1 NO 17-331220 6 BUFFER RING 1 NO 27-151111 7 AIR DISTRIBUTOR 1 NO 12-8J8000 8 “O” RING FOR AIR DISTRIBUTOR 1 NO 37-10604H 9 INNER CYLINDER 1 NO 42-8J8000 10 PISTON 1 NO 55-8C8000 PISTON [JDM80DH] 1 NO 55-8C8002 PISTON[JDM80SD] 1 NO 55-8C8003 11 WEAR SLEEVE 1 NO 45-8C8000 WEAR SLEEVE[JDM80DH] 1 NO 45-8C8002 WEAR SLEEVE[JDM80SD] 1 NO 45-8C8003 12 PISTON RETAINER RING 1 NO 89-140635 13 GUIDE BUSH 1 NO 65-8C8000 GUIDE BUSH[JDM80DH/SD] 1 NO 65-8C8001 14 “O”RING FOR GUIDE BUSH 2 NO 37-13204H 15 BIT RETAINER RING 1 NO 99-141037 BIT RETAINER RING[JDM80DH] 1 NO 99-141033 BIT RETAINER RING[JDM80SD] 1 NO 99-140944 16 “O” FOR BIT RETAINER RING 1 NO 37-13204H 17 DRIVE SUB SPACER 1 NO 29-181610 18 DRIVE SUB[JDM80QL] 1 NO 75-8J8000 DRIVE SUB[JDM80DH] 1 NO 75-8C8000 DRIVE SUB[JDM80SD] 1 NO 75-8C8001 SERVICE KI T (S.NO: 2,4,5,6,8,14&16) 1 SET 8J8000QLK HAMMER ASSEMBLY 1 NO 34-8C8000QL-41ARMS HAMMER ASSEMBLY 1 NO 34-8C8000QL-41ARMS/R HAMMER ASSEMBLY 1 NO 34-8C8001DH-41ARMS HAMMER ASSEMBLY 1 NO 34-8C8001DH-41ARMS/R HAMMER ASSEMBLY 1 NO 34-8C8000SD-41ARMS HAMMER ASSEMBLY 1 NO 34-8C8000SD-41ARMS/R A DEDICATED TOOL FOR 8” DRILLING SL.NO DESCRIPTION UNIT DIMENSION 1 HAMMER LENGTH W/O BIT mm 1334.0 2 HAMMER OUTSIDE DIA mm 182.0 3 HAMMER WEIGHT kg 190.0 4 CYLINDER BORE mm 149.0 5 PISTON STROKE mm 80.0 (approx.) 6 PISTON WEIGHT kg 42.0 7 HOLE SIZES mm 200 - 305 8 WRENCH SIZE A/F mm A/F 140 / W-50 9 SUITABLE SHANK ----- QL80( With Foot Valve) SUITABLE SHANK ----- DH380( With Foot Valve) SUITABLE SHANK ----- S80( With Foot Valve) HAMMER SPECIFICATION JDM SERIES 1 2 3 4 5 6 7 8 11 9 12 13 14 15 16 17 QL80 * TWO START THREAD ON TOP SUB & DRIVE SUB CFM 240 670 1890 1230 2650 PSI 100 200 400 300 500 JDM80QL / DH / SD Air Consumption BPM 1020 1440 2040 1770 2280 10 17

46. 46 DTH PRODUCT CATALOGUE JDM55QL / DH HAMMER SL.NO NAME OF THE ITEM QTY PART NO 1 TOP SUB 1 NO 15-5C5500-31ARM TOP SUB 1 NO 15-5C5500-27ARM 2 CHOKE (FULL/HALF/QUARTER) 1 NO 47-0127N/(A)(C)(D) 3 CHECK VALVE 1 NO 19-24101R 4 SPRING 1 NO 17-221017 5 STEEL MAKEUP RING 1 NO M9-100705 6 LOCK RING 1 NO 29-100712 7 AIR DISTRIBUTOR 1 NO 12-5C5500 8 “O” RING FOR AIR DISTRIBUTOR 1 NO 37-06803H 9 SEATING RING 1 NO 79-100910 10 “O” RING FOR SEATING RING 1 NO 37-06002H 11 INNER CYLINDER 1 NO 42-5C5500 12 PISTON[JDM55QL] 1 NO 55-5C5500 PISTON[JDM55DH] 1 NO 55-5C5501 13 WEAR SLEEVE 1 NO 45-5C5500 14 PISTON RET RING 1 NO 89-090324 15 GUIDE BUSH[JDM55QL] 1 NO 65-5C5500 GUIDE SPACER[JDM55DH] 1 NO 29-100818 16 “O” RING FOR GUIDE BUSH 1 NO 37-09003H 17 BIT RETAINER RING[JDM55QL] 1 NO 99-100716 BIT RETAINER RING[JDM55DH] 1 NO 99-100718 18 “O” RING FOR BIT RETAINER RNG 1 NO 37-08402H 19 DRIVE SUB SPACER (Copper shim) 1NO 77-12101C 20 DRIVE SUB[JDM55QL] 1 NO 75-5C5500 DRIVE SUB[JDM55QL] 1 NO 75-5C5500/L DRIVE SUB[JDM55DH] 1 NO 75-5C5502 DRIVE SUB[JDM55DH] 1 NO 75-5C5502/L SERVICE KIT (S.NO:2,4,8,10,16&18) 1 SET 5C5500QLK HAMMER ASSEMBLY[JDM55QL] 1 NO 34-5C5500QL-31ARMR HAMMER ASSEMBLY[JDM55QL] 1 NO 34-5C5500QL-31ARMR/L HAMMER ASSEMBLY[JDM55QL] 1 NO 34-5C5500QL-27ARMR HAMMER ASSEMBLY[JDM55DH] 1 NO 34-5C5500DH-31ARMR HAMMER ASSEMBLY[JDM55DH] 1 NO 34-5C5500DH-31ARMR/L A DEDICATED TOOL FOR 5.5” DRILLING SL.NO DESCRIPTION UNIT DIMENSION 1 HAMMER LENGTH W/O BIT mm 994.0 2 HAMMER OUTSIDE DIA mm 124.0 3 HAMMER WEIGHT kg 70.0 4 CYLINDER BORE mm 99.80 5 PISTON STROKE mm 80.0 (opprox.) 6 PISTON WEIGHT kg 15.0 7 HOLE SIZES mm 140-165 8 WRENCH SIZE A/F mm A/F 90.0 / W-50.0 9 SUITABLE SHANK ----- QL50 (With Foot Valve) SUITABLE SHANK ----- DMD50 (With Foot Valve) HAMMER SPECIFICATION 15 16 17 18 19 QL 50 1 2 3 4 5 6 7 8 9 10 11 12 13 14 JDM SERIES * TWO START THREAD ON TOP SUB & DRIVE SUB CFM 140 390 1110 720 1550 PSI 100 200 400 300 500 JDM55QL / DH Air Consumption BPM 1155 1635 2310 2000 2585

11. 11 DTH PRODUCT CATALOGUE SD4 MM Inch Outer Front KG LBS 105 4 1/8 2 14X8 12X6 9.1 20.1 36-41967105S 110 4 1/3 2 14X8 12X6 9.3 20.5 36-41967110S 115 4 1/2 2 14X8 12X6 9.3 20.7 36-41967115S 121 4 3/4 2 14X8 12X7 9.8 21.6 36-41977121S 127 5 2 14X8 14X8 10.4 23.0 36-41989127S 130 5 1/8 2 14X8 14X8 10.8 23.8 36-41989130S 165 6 1/2 2 16X8 14X10 13.2 29.1 36-4190C165S Diameter Flush Hole Buttons Dia x Qty Weight Product No Diameter Flush Hole Buttons Dia x Qty Weight Product No MM Inch Outer Front KG LBS 105 4 1/8 2 14X8 12X6 9.0 19.8 36-41867105S 110 4 1/3 2 14X8 12X6 9.2 20.2 36-41867110S 115 4 1/2 2 14X8 12X7 9.6 21.1 36-41877115S 127 5 2 14X8 14X8 10.5 23.1 36-41889127S 130 5 1/8 2 14X8 14X8 10.8 23.8 36-41889130S Diameter Flush Hole Buttons Dia x Qty Weight Product No SD5 MM Inch Outer Front KG LBS 125 4 15/16 2 14X8 14X7 13.0 28.7 36-51979125S 127 5 2 14X8 14X7 13.2 29.1 36-51979127S 140 5 1/2 2 16X8 16X8 15.5 34.1 36-5198D140S 146 5 3/4 2 16X8 16X8 15.9 35.1 36-5198D146S 152 6 2 16X8 16X10 16.6 36.6 36-5190D152S 165 6 1/2 2 16X8 16X10 17.5 38.6 36-5190D165S Diameter Flush Hole Buttons Dia x Qty Weight Product No MM Inch Outer Front KG LBS 125 4 15/16 2 14X8 14X7 13.0 28.6 36-51779125S 127 5 2 14X8 14X7 13.2 29.0 36-51779127S 140 5 1/2 2 16X8 16X8 15.6 34.3 36-5178D140S 146 5 3/4 2 16X8 16X7 15.9 35.0 36-5177D146S 152 6 2 16X8 16X10 16.6 36.6 36-5170D152S 165 6 1/2 2 16X8 16X10 17.5 38.6 36-5170D165S Diameter Flush Hole Buttons Dia x Qty Weight Product No MM Inch Outer Front KG LBS 127 5 2 14X8 14X7 12.9 28.4 36-51879127S 140 5 1/2 2 16X8 14X8 15.5 34.1 36-5188C140S 146 5 3/4 2 16X8 16X8 16.0 35.0 36-5188D146S Diameter Flush Hole Buttons Dia x Qty Weight Product No SD SHANKS FLAT FACE MM Inch Outer Front KG LBS 105 4 1/8 2 14X8 12X6 9.1 20.0 36-41767105S 110 4 1/3 2 14X8 12X6 9.2 20.4 36-41767110S 115 4 1/2 2 14X8 12X6 9.4 20.7 36-41767115S 127 5 2 14X8 14X7 10.3 22.8 36-41779127S 130 5 1/8 2 14X8 14X7 10.5 23.2 36-41779130S CONCAVE CONVEX FLAT FACE CONCAVE CONVEX DTH SHANKS

56. 56 DTH PRODUCT CATALOGUE JDC80QL HAMMER SL.NO NAME OF THE ITEM QTY PART NO 1 TOP SUB 1 NO 15-8J8000-41ARM 2 “O” RING FOR TOP SUB 1 NO 37-14005H 3 CHECK VALVE 1 NO 19-37138R 4 SPRING 1 NO 17-331220 5 BUFFER RING 1 NO 27-151111 6 AIR DISTRIBUTOR[JDC80QL] 1 NO 12-8J8000 AIR DISTRIBUTOR[JDC80DH] 1 NO 12-8J8002 7 “O” RING FOR AIR DISTRIBUTOR 1 NO 37-10604H 8 INNER CYLINDER[JDC80QL] 1 NO 42-8J8000 INNER CYLINDER[JDC80DH] 1 NO 42-8J8001 9 PISTON 1 NO 52-8J8000 10 WEAR SLEEVE[JDC80QL] 1 NO 45-8J8000 WEAR SLEEVE[JDC80DH] 1 NO 45-8J8001 11 PISTON RETAINER RING 1 NO 89-140635 12 “O”RING FOR GUIDE BUSH 3 NO 37-13204H 13 GUIDE BUSH[JDC80QL] 1 NO 65-8J8000 GUIDE BUSH[JDC80DH] 1 NO 65-8J8001 14 BIT RETAINER RING[JDC80QL] 1 NO 99-141037 BIT RETAINER RING[JDC80DH] 1 NO 99-141039/A 15 “O” FOR BIT RETAINER RING 1 NO 37-13204H 16 “O” FOR BIT RETAINER RING[JDC80DH] 1 NO 37-11602H 17 DRIVE SUB SPACER 1 NO 29-181610 DRIVE SUB[JDC80QL] 1 NO 75-8J8000 DRIVE SUB[JDC80QL] 1 NO 75-8J8000/L DRIVE SUB[JDC80DH] 1 NO 75-8J8001 18 CHOKE (FULL/HALF/QUARTER) 1NO 47-0147N(A)(C)(D) SERVICE KI T (S.NO: 2,4,5,7,12,15&18) 1 SET 8J8000QLK HAMMER ASSEMBLY[JDC80QL] 1 NO 34-8J8000QL-41ARMS HAMMER ASSEMBLY[JDC80QL] 1 NO 34-8J8000QL-41ARMS/L HAMMER ASSEMBLY[JDC80DH] 1 NO 34-8J8001DH-41ARMS A DEDICATED TOOL FOR 8” DRILLING SL.NO DESCRIPTION UNIT DIMENSION 1 HAMMER LENGTH W/O BIT mm 1353.60 HAMMER LENGTH W/O BIT[JDC80DH] mm 1371.0 2 HAMMER OUTSIDE DIA mm 182.0 3 HAMMER WEIGHT kg 198.0 HAMMER WEIGHT[JDC80DH] kg 180.0 4 CYLINDER BORE mm 149.0 5 PISTON STROKE mm 80.0 (approx.) 6 PISTON WEIGHT kg 41.60 7 HOLE SIZES mm 200 - 254 8 WRENCH SIZE A/F mm A/F 140 / W-50 9 SUITABLE SHANK ----- QL80( W/O Foot Valve) SUITABLE SHANK ----- DHD380( W/O Foot Valve) HAMMER SPECIFICATION JDC SERIES 1 2 3 4 5 6 7 8 9 13 14 15 17 QL80 12 10 16 11 * TWO START THREAD ON TOP SUB & DRIVE SUB CFM 215 605 1710 1110 2390 PSI 100 200 400 300 500 JDC80QL / DH Air Consumption BPM 920 1305 1845 1595 2060 18

80. 80 DTH PRODUCT CATALOGUE ASSEMBLY 9 10 8 9 11 12 13 14 15 9 7 6 5 9 1 4 3 2 • Place the inner cylinder(7) and air distributor(6) along with the “o” ring (5) in the wear sleeve. • Place the buffer ring (4), spring (3) and check valve (2) in the wear sleeve. Screw-up the top sub (1) and the wear sleeve (9) • Place the guide bush (11), along with “0” ring (12) in the wear sleeve (9). • Place the bit retainer ring (13), along with its “0” ring (14). • Screw-up the drive sub (15) in the wear sleeve (9). • Inspect all the components free from burrs, dirt. Liberally coat all the parts with good quality of drill oil and threads with grease. • Place the piston (8) and piston retainer ring (10) in the wear sleeve (9). A. When dismantling the hammer it is essential that cylinder are clamped in correct position, away from threads, which can be damaged. B. Break the tap joint between the wear sleeve(9) and the drive sub (15). C. Unscrew and remove the drill bit and drive sub (15) D. Remove the drive sub (15) bit retainer ring (13) along with its “O” ring (14). E. Unscrew and remove the top sub (1) from wear sleeve (9). F. Take out the check valve (2), spring (3), buffer ring (4) from the wear sleeve (9). G. Take out the air distributor (6) along with its “O ”ring(5), inner cylinder(7) from the wear sleeve(9).sleeve (9). H. Remove the aligner (11) along with its “O”ring(12) from the wear sleeve(9). I. Remove the piston retainer ring(10) and piston(8) from the wear sleeve(9). CLAMPS DTH HAMMERS MAINTENANCE DISASSEMBLY ASSEMBLY

78. 78 DTH PRODUCT CATALOGUE FCR 55 HAMMER A DEDICATED TOOL FOR 5.0” DRILLING SL.NO DESCRIPTION UNIT DIMENSION 1 HAMMER LENGTH W/O BIT mm 1245.0 2 HAMMER OUTSIDE DIA mm 121.0 3 HAMMER WEIGHT kg 72.0 4 CYLINDER BORE mm 99.86 5 PISTON STROKE mm 80.0 (approx.) 6 PISTON WEIGHT kg 13.550 7 HOLE SIZES mm 140-177.8mm 8 WRENCH SIZE A/F mm A/F 94.0 /W-50.0 9 SUITABLE SHANK ----- PR40 HAMMER SPECIFICATION RC SERIES SL.NO NAME OF THE ITEM QTY PART NO 1 ADAPTOR 1NO 13-5CR5500-41/2”REMF ADAPTOR 1NO 13-5CR5500-4”METZKE 2 “O” RING FOR ADAPTOR 2NO 37-05503H 3 ADAPTOR TUBE 1NO 23-5CR5500 4 AIR SCREEN TOP LOAD 1NO 33-5CR5500 5 CIRCLIP 1NO 89-040203 6 CIRCLIP 1NO 89-080325 7 CHECK VALVE 1NO 19-66061M 8 “O”RING FOR CHECK VALVE 1NO 37-04305H 9 SPRING 1NO 17-531108 10 STEEL MAKE UP RING 1NO M9-080605 11 VITON MAKE UP RING 1NO 29-080613 12 “O” RING FOR DISTRIBUTOR 1NO 37-04903H 13 DISTRIBUTOR 1NO 12-5CR5500 14 “O” RING FOR SAMPLE TUBE VENTURI 2NO 37-04302H 15 “O” RING FOR SAMPLE TUBE VENTURI 1NO 37-04703H 16 SAMPLE TUBE VENTURI 1NO 43-5CR5500 17 “O” RING FOR MOUNT SAMPLE TUBE 1NO 37-07603H 18 MOUNT SAMPLE TUBE 1NO 53-5CR5500 19 INNER CYLINDER 1NO 42-5CR5500 20 PISTON 1NO 52-5CR5500 21 WEAR SLEEVE 1NO 45-5CR5500 22 PISTON RETAINER RING 1NO 89-100428 23 “O”RING FOR BUSH DRIVE SUB 1NO 37-08605H 24 “O”RING FOR BUSH DRIVE SUB 1NO 37-09003H 25 BUSH DRIVE SUB 1NO 65-5CR5500 26 “O”RING FOR BIT RETAINER RING 1NO 37-08303H 27 BIT RETAINER RING 1NO 99-090819 28 DRIVE SUB RING 1NO 63-1381008 29 DRIVE SUB 1NO 75-5CR5500 SEAL KIT(2,8,12,14,15,17,23,24,&26) 1SET 5CR5500PRK HAMMER ASSEMBLY 1NO 44-5CR5500PR-41/2”REMFS HAMMER ASSEMBLY 1NO 44-5CR5500PR-4”METZKEFS 20 22 25 26 21 27 28 PR40 2 1 4 3 6 5 8 7 10 9 11 16 14 12 13 15 17 18 19 23 24 29 CFM 450 600 900 750 1050 PSI 250 300 400 350 450 FCR55 Air Consumption BPM 1390 1520 1640 1760 1860 1200 1960 500

91. 91 DTH PRODUCT CATALOGUE 36 65 N E H 172 S BIT CODE SHANK CODE BUTTON COMBINATION SD4 41 SD5 51 SD6 61 SD8 81 SD10 S1 SD12 S2 RK1 R1 RK3 R3 MACH303 34 MACH44 44 MACH50 54 MX40 X4 QL40 45 QL50 55 QL60 65 QL80 85 CHEETHA 37 NUMA 100 N1 NUMA 120 N2 DHD17 87 PUMA P8 DHD3.5 33 DHD340 43 DHD350 53 DHD360 63 DHD380 83 BR2 22 BR3 32 BR33 42 COP34 35 4.5 47 PANTHER DIAMETER F.H G.BUT CODE 2 6 1 2 7 4 2 8 7 2 10 I 2 12 L 3 9 N 3 12 Q 3 14-25 U 3 25& Above V FACE DESIGN F.H G.BUT CODE 2 6 2 2 7 5 2 8 8 2 10 J 3 9 O 3 12 R 3 14 & Above W 2 12 A FACE DESIGN FOR CONCAVE FACE DESIGN FOR CONVEX F.H G.BUT CODE 2 6 3 2 7 6 2 8 9 2 10 K 2 12 M 2 14 & Above H 3 9 P 3 12 S 3 14 T 3 15-25 X 3 25& Above Y 1 6 Z FACE DESIGN FOR FLAT FACE G F CODE S S S B B B P P P K K K S B C S P D S K E P B F B P G S – SPHERICAL B – BALLASTIC P – PARABOLIC K - SPIKE SHAPE COMBINATION GXF C 11X11 Z 12X10 1 12X11 2 12X12 3 13X11 4 13X12 5 13X13 6 14X12 7 14X13 8 14X14 9 16X12 A 16X13 B 19X12 F 19X13 G 19X14 H 19X16 I 19X19 J 14X11 K 18X18 L 19X18 M 18X14 N 18X16X14 O 10X10 P 16X14X13 Q 11X10X9 R 20X18 S 14X13X12 T 11X10 U 14X12X11 V 13 X 10 W 19X18X16 X 20 X 20 Y 22 X 22 A1 16X14X12 A2 20 X 19 A3 FACE BUTTONS NO.OF FB C 3 3 4 4 5 5 6 6 7 7 8 8 9 9 10 0 11 1 12 2 13 E 14 F 15 G 16 H 17-25 I 25-40 J 40 ABOVE K SPECIFICATION CHARTS BUTTON BIT QLX40 Q4 TD40 T4 16X14 C 16X16 D 18X16 E N L / WITHOUT FOOTVALVE L LASER HARD FACE C CROSS FLUSH HOLE G GAUGE PROTECTION BUTTON W WASARA SHANK R RETRACT BUTTON ADD ON DESIGN FEATURE FD4 49 COP54 52 MC30 C3 COPROD89 89 F.H G.BUT CODE 2 8 K1 2 10 K2 2 12 K3 2 14 & Above K4 3 9 K5 3 12 K6 3 14 & Above K7 4 12 K8 4 16 & Above K9 FACE DESIGN FOR KAVEX FACE SPEC CHRATS